August 25 Release version 1.57b5 ================================ - Added support for predictive W/S switch - Tuned ECAM for ADR 1+2+3 fault - Fixed RAT extention solenoid 2 not working - Do not show TERR indication on ND PLAN mode during terrain test August 16 Release version 1.57b4 ================================ - Fixed ECAM issues after takeoff with IAE engine selection - Round fuel values to 20's - Control ECAM SPD BRK DISAGREE message when speedbrake lever is not down and speedbrake inhibit active August 8 Release version 1.57b3 =============================== - Adjusted yaw tuning to precent oscillations August 8 Release version 1.57b2 =============================== - Adjusted pitch limit PFD indication and normal law behavior - Autopilot roll tuning August 2 Release version 1.57b1 =============================== - Fixed TO waypoint in FPLN page should count down actual distance. - [Datalink printer] Added further data to base template header - Fixed cabin pressure rate issues - Added support for FS2CREW RAAS lvar master switch - Do not show weather radar status data in ND when IRS not aligned July 22 Release version 1.56 ============================ Systems: - Do not allow generator disconnect when engine not running - Scroll AOC messages per page instead of per line - Brake temperature tuning - Set APU EGT to OAT by default - Do not show REV state in E/WD if fadec not operational - Fix issue with speedbrakes during A/P flight - Fixed AUTO FEED FAULT sometimes appearing after center tank reaches low level - Dual NAV RA failure should disable reactive w/s and TCAS - Fixed GWPS terrain still available during IR1 fault - Approach message should not be available in ND during dual FMGC failure - Added gates Blower running, extract running and cockpit air low/med/high - Added gates for autopilot enabled and disabled - Added SDK variable aircraft.pneumatic.cockpitAir - Added circuitbreakers for engine oil press/qty transmitters and tyre press/temp transmitters - If SEC 1+2+3 failure, use flap handle 2 state instead of gear for direct law trigger - Ignore EFIS QNH input when QNH set to STD - Dual ADR fault will cause Flap 1+F in the air with flaps set to 1 - ADR 1+2 fault should cause GPW TERR Fault - When in NAV override mode, RMP should start in course mode when selecting ILS or VOR - Revised logic for autoland warning light - Fixed rudder trim going over rudder travel limiter - Fixed GPWS alert not disengaging when switching off GPWS SYS when alert active - Inhibit eng oil pressure advisory during shutdown - Allow non ILS approach to activate with dual RA failure - Adjusted engine start parameters to prevent fuel flow before 22% N2 in CFM - When engine mode selector set to START, only show ENGINE page during startup phase - Fixed hydraulic pressure not recovered after resetting failure - Reversers should not be available if more than 1 SEC fails - DC BUS 1+2 fault should cause PACK 2 loss and APU loop A+B loss - Fixed Idle N1 not increasing based on bleed demand when A/T is on - Improved MCDU behavior during single FM failure - Adjusted outflow valve size to have finer control during manual pressure operation FMS: - Do not reset FMA and MCDU after landing during auto fms reset - Move to status page after reset - Do not treat visual approach as non precision - Only update cruise alt from FCU altitude if alt pushed or pulled - Recalulate vnav data during cruise more often - Some LNAV rendering improvements - Improvements in LNAV offsets - Do not enable A/THR on ground when thrust levers at TOGA but engines shut down - Revert FINAL to default modes when passing MAP - Do not trigger CRZ FL ABOVE MAX FL message unless weight is known on ground - Do not show FMA DH/MDA unless in approach or cruise and close to descend - Added range checking perf appr for baro/radio minimums and changed FMA to indicate BARO/RADIO instead of MDA/DH - Fixed NEW WAYPOINT RETURN prompt always going to FPLN-A instead of previous page - Fixed OPT ALT showing more than certified max alt - Fixed CSTR labels missing in PLAN mode if IRS not fully aligned - Improvements to FMS DONE phase - Adjusted range change for baro minimums - Check input of CDU new waypoint page to better detect improper formatting - Fixed error in FLS anchor point calculation - Fixed issue with Constant mach segments clearing too soon - Fix incorrect MAX ALT during single engine operation Hardware: - [CPFlight] Added ECAM panel - Added XPDR light for FSCockpit hardware Displays: - Added ND declutter for SID/STAR at higher zoom levels - Use lower display threshold of .45 mach during deceleration - Keep mach visible in PFD when LS is active - Do not show transit state of pack valves - Adjust PFD blink frequencies and FMA box sizes - Fix v/dev bar slightly overlapped by ATT - Update mask of ND Rose display to prevent route drawing through TERR data box - Roll pointer should remain yellow - Slightly adjusted pdf Mach indication to match location of QNH Misc: - Add gate for static inverter bus - Added predictive windshear by arming through the IOS - Added support for new IVAO data format in ProSimIOS - Fixed SDK access to switches with hardware latched to software momentary not working correctly - Added switch 1/2 gates for better startup sound setup - [Datalink] Added printer option - [Datalink] Added base template note: This base template can be used to customize header/footer and add extra lines at the end to allow cutting space depending on the printer used. - Fixed potential scenery object airport skipped when delete information is not set - Fixed ILS heading issue for scenery items that use non fixed heading in MSFS2020 - Improved generic TCP driver to only send out numerical values that changed - Adjusted wind readout in current weather of ProSimIOS - Added DCDU display output to SDK - Exposed "Elevator trim motor" numerical output to drive trim motor - Transmit seatbelt on information over simconnect to simulator - Fixed cockpit setup "metar provider" selection not saving - Fixed TCAS intruders added by ProSimIOS not correctly removed again - Removed ACP SPKR key control and link intercom speaker control to MIP loudspeaker input - Fixed issues with door synchronisation when doors are controlled from external sources - Renamed Hung start to Stall/Hung start July 21 Release version 1.56b13 =============================== - Fixed Idle N1 not increasing based on bleed demand when A/T is on - Fix incorrect MAX ALT during single engine operation - Added XPDR light for FSCockpit hardware - Improved MCDU behavior during single FM failure July 19 Release version 1.56b12 =============================== - Adjusted outflow valve size to have finer control during manual pressure operation - Slightly adjusted pdf Mach indication to match location of QNH - Renamed Hung start to Stall/Hung start - DC BUS 1+2 fault should cause PACK 2 loss and APU loop A+B loss - Reversers should not be available if more than 1 SEC fails July 13 Release version 1.56b11 =============================== - Fixed hydraulic pressure not recovered after resetting failure - When engine mode selector set to START, only show ENGINE page during startup phase - Adjusted engine start parameters to prevent fuel flow before 22% N2 in CFM - Fixed issues with door synchronisation when doors are controlled from external sources - Removed ACP SPKR key control and link intercom speaker control to MIP loudspeaker input July 7 Release version 1.56b10 ============================== - Fixed issue with Constant mach segments clearing too soon - Fixed error in FLS anchor point calculation - Check input of CDU new waypoint page to better detect improper formatting July 4 Release version 1.56b9 ============================= - Fixed TCAS intruders added by ProSimIOS not correctly removed again - Fixed cockpit setup "metar provider" selection not saving - Adjusted range change for baro minumums - Improvements to FMS DONE phase - Fixed CSTR labels missing in PLAN mode if IRS not fully aligned - Transmit seatbelt on information over simconnect to simulator - Allow non ILS approach to activate with dual RA failure - Exposed "Elevator trim motor" numerical output to drive trim motor - Inhibit eng oil pressure advisory during shutdown - Fixed GPWS alert not disengaging when switching off GPWS SYS when alert active - Fixed OPT ALT showing more than certified max alt July 1 Release version 1.56b8 ============================= - Fixed NEW WAYPOINT RETURN prompt always going to FPLN-A instead of previous page - Added DCDU display output to SDK - Adjusted wind readout in current weather of ProSimIOS June 24 Release version 1.56b7 ============================== - Added range checking perf appr for baro/radio minimums and changed FMA to indicate BARO/RADIO instead of MDA/DH - Improved generic TCP driver to only send out numerical values that changed - Fixed rudder trim going over rudder travel limiter - Revised logic for autoland warning light - When in NAV override mode, RMP should start in course mode when selecting ILS or VOR - Fixed ILS heading issue for scenery items that use non fixed heading in MSFS2020 - Fixed potential scenery object airport skipped when delete information is not set June 20 Release version 1.56b6 ============================== - [CPFlight] Added ECAM panel - ADR 1+2 fault should cause GPW TERR Fault - Dual ADR fault will cause Flap 1+F in the air with flaps set to 1 - Roll pointer should remain yellow - Ignore EFIS QNH input when QNH set to STD - If SEC 1+2+3 failure, use flap handle 2 state instead of gear for direct law trigger - Added circuitbreakers for engine oil press/qty transmitters and tyre press/temp transmitters June 7 Release version 1.56b5 ============================= - Added SDK variable aircraft.pneumatic.cockpitAir - Added gates Blower running, extract running and cockpit air low/med/high - Added gates for autopilot enabled and disabled - Slight tuning of MACH font in PFD - [Datalink] Added base template note: This base templace can be used to customize header/footer and add extra lines at the end to allow cutting space depending on the printer used. May 31 Release version 1.56b4 ============================= - [Datalink] Added printer option May 30 Release version 1.56b3 ============================= - Dual NAV RA failure should disable reactive w/s and TCAS - Fixed GWPS terrain still available during IR1 fault - Approach message should not be available in ND during dual FMGC failure - Added switch 1/2 gates for better startup sound setup - Update mask of ND Rose display to prevent route drawing through TERR data box - Do not show FMA DH/MDA unless in approach or cruise and close to descend - Fixed AUTO FEED FAULT sometimes appearing after center tank reaches low level - Fixed SDK access to switches with hardware latched to software momentary not working correctly - Do not trigger CRZ FL ABOVE MAX FL message unless weight is known on ground May 16 Release version 1.56b2 ============================= - Fix issue with speedbrakes during A/P flight - Fix v/dev bar slightly overlapped by ATT - Revert FINAL to default modes when passing MAP - Adjust PFD blink frequencies and FMA box sizes - Do not show REV state in E/WD if fadec not operational - Do not enable A/THR on ground when thrust levers at TOGA but engines shut down - Do not show transit state of pack valves - Set APU EGT to OAT by default - Improvements in LNAV offsets - Some LNAV rendering improvements May 3 Release version 1.56b1 ============================ - Added support for new IVAO data format in ProSimIOS - Keep mach visible in PFD when LS is active - Use lower display threshold of .45 mach during deceleration - Recalulate vnav data during cruise more often - Brake temperature tuning - Added predictive windshear by arming through the IOS - Scroll AOC messages per page instead of per line - Added ND declutter for SID/STAR at higher zoom levels - Only update cruise alt from FCU altitude if alt pushed or pulled - Do not allow generator disconnect when engine not running - LNAV fixes - Do not treat visual approach as non precision - Add gate for static inverter bus - Move to status page after reset - Do not reset FMA and MCDU after landing during auto fms reset May 24 Release version 1.55 =========================== Systems: - Added IAE engine fail ecam - Fix exhaust/blower IOS check items - Added F/CTL and SFCS maintenance ECAM indications - Allow APU fire loop test to shut down apu - Fixed issue where center pumps do not switch on when wing tanks have enough room - Fuel pump lights should flash momentarily when pumps turned on - Enable IDG later during engine start - Reworked engine cooldown - Revised apu fire system and fdu fire tests - Refined fire loops and added individual columns for fire button leds - Fix crossfeed not taking fuel from two tanks - Fix pack valves not automatically closing when engine mode set to start and fadecs are off - Fix hot start not working - Fixed issue with IDG oil pressure during engine failure - Tune brake temperatures - Tuned pneumatic valves and packs - Fixed hydraulic leak not causing pressure loss Displays: - Weather/terrain radar fixes - Prevent markers from extending into missed approach path if path not visible - Dot not box FMA V/S or FPA modes when target values change - Fixed flaps/slats not showing failed state when engine is shut down - Revised representation of APU generator data on ECAM - Move cancelled cautions to bottom of screen and display in white - Fix wind not displayed in the air with gs < 100 - Adjusted layout of chrono in ND - Reworked PFD to be more accurate - Align FOB data on upper ecam and lower ecam - Fixed ISIS mach indication - Keep N2 inverted during engine start until after n2 > 58 - Do not show slats amber during engine start on ground - Fix ground alt in alt tape - Fixed PFD alt tape not showing next FMS level off altitude - Fixed PFD next altitude target not showing FMS targets - Show route as dashed if no FMA mode is active FMS: - Fixed issue with T/D shifting after activating descend - Fix managed climb pitch and F/D movement when transitioning from alt hold to climb - Fixed a crash in vnav - LNAV changes to allow more bypasses - LNAV fixes - Use a slower climbrate when in levelchange and acceleration is required - Do not engage alpha floor when over mach .6 or when TCAS is active or engine out and flap/slats extended - Revert to basic mode if G/S and LOC armed and either signal lost for 7 seconds - Allow throttle idle to cancel toga lock Also display A FLOOR on E/WD during toga lock - When passing into a discontinuity, do not sequence discontinuity until 5NM from next waypoint - Do not show VNAV calculations during FMS go around and activate open climb after SRS - Fixed issue with calculation of fuel and EFOB during flight - Allow DES to be active when LOC has captured (would revert to V/S previously) - Fixed a VNAV issue where aircraft would not follow correct path on descend MCDU: - Fixed PERF DES managed speed should update when new values entered - perf approach transition level should be FL not ALT - Add input checks to transition altitude/level - Fixed INIT B zfw/cfg formatting - Fixed approach VIA reset after each flightplan change - Changed ordering of ils approach types in MCDU - Fixed CRZ ALT in PROG page should be white dashes in approach phase Hardware: - Fix for speedbrake/flap handle input issues - Added skalarki ASP CALL/MECH/ATT light activation - Fixed skalarki ASP backlight indicators - Added option in ProsimA322-system hardware options screen to disable ground trim wheel lock - Added sogeclair driver - [FDS Ethernet] Fixed MCDU not working Misc: - NO NAV INTERCEPT message should reset when pulling HDG - Do not clear ICAO entries in weather request page when weather type switched - Added option to link only left + right QNH and leave ISIS independent - Fix uplink cruise winds at wrong altitudes - Fixed temperature layers in ProSimIOS when Active Sky was not used - Lower n1 Avail threshold - Do not set Cost index, cruise altitude and flight number from uplink data - Fixed n2 indication lagging behind during start causing FF to appear before 22% - Fix issues with refueling - Reset DCDU message index when last message cleared - Fixed error in descend speed table - Fixed issues in refueling panel - Added ground preconditioned air option - Activate VHF1 send on ASP1 and 2 on powerup - Prevent spoiler retraction and autobrake disconnect after bounce - Use pressure altitude to calculate indicated altitude for FS2020 to prevent altitude differences - Fix HardwareConnector versioning - Added settings option to enable confirmation dialog before ProSimIOS close - Fixed failure conditions of arm failures not always correctly shown in ProSimIOS April 22 Release version 1.55b22 ================================ - [FDS Ethernet] Fixed MCDU not working - Fix HardwareConnector versioning April 18 Release version 1.55b21 ================================ - Added settings option to enable confirmation dialog before ProSimIOS close - Fixed failure conditions of arm failures not always correctly shown in ProSimIOS - Fixed CRZ ALT in PROG page should be white dashes in approach phase - Fixed a VNAV issue where aircraft would not follow correct path on descend - Fixed hydraulic leak not causing pressure loss - Allow DES to be active when LOC has captured (would revert to V/S previously) April 5 Release version 1.55b20 =============================== - Fixed issue with calculation of fuel and EFOB during flight April 4 Release version 1.55b19 =============================== - Added sogeclair driver - Tuned pneumatic valves and packs April 1 Release version 1.55b18 =============================== - Use pressure altitude to calculate indicated altitude for FS2020 to prevent altitude differences March 31 Release version 1.55b17 ================================ - Do not show VNAV calculations during FMS go around and activate open climb after SRS - Show route as dashed if no FMA mode is active - Added option in ProsimA322-system hardware options screen to disable ground trim wheel lock - When passing into a discontinuity, do not sequence discontinuity until 5NM from next waypoint - Tune brake temperatures March 22 Release version 1.55b16 ================================ - Prevent spoiler retraction and autobrake disconnect after bounce March 21 Release version 1.55b15 ================================ - Fixed PFD next altitude target not showing FMS targets March 21 Release version 1.55b14 ================================ - Fixed issue with IDG oil pressure during engine failure - Activate VHF1 send on ASP1 and 2 on powerup - Allow throttle idle to cancel toga lock Also display A FLOOR on E/WD during toga lock - Added ground preconditioned air option - Fixed issues in refueling panel March 16 Release version 1.55b13 ================================ - Fixed error in descend speed table - Fixed PFD alt tape not showing next FMS level off altitude March 14 Release version 1.55b12 ================================ - Fix hot start not working - Reset DCDU message index when last message cleared - Fix issues with refueling - Revert vnav speed handling during descent to older model March 10 Release version 1.55b11 ================================ - Fixed n2 indication lagging behind during start causing FF to appear before 22% - Fix ground alt in alt tape - Do not set Cost index, cruise altitude and flight number from uplink data - Do not show slats amber during engine start on ground - Lower n1 Avail threshold - Keep N2 inverted during engine start until after n2 > 58 - Fix pack valves not automatically closing when engine mode set to start and fadecs are off March 6 Release version 1.55b10 =============================== - Fixed temperature layers in ProSimIOS when Active Sky was not used - Fixed skalarki ASP backlight indicators March 4 Release version 1.55b9 ============================== - Fixed ISIS mach indication - Revert to basic mode if G/S and LOC armed and either signal lost for 7 seconds March 4 Release version 1.55b8 ============================== - Revised THR IDLE descend mode. THR IDLE will remain active in idle descent segments and use power to maintain in managed speed range - Fix uplink cruise winds at wrong altitudes - Align FOB data on upper ecam and lower ecam - Reworked PFD to be more accurate - Fix crossfeed not taking fuel from two tanks - Revised apu fire system and fdu fire tests - Refined fire loops and added individual columns for fire button leds - Added skalarki ASP CALL/MECH/ATT light activation - Enable IDG later during engine start - Reworked engine cooldown - Use a slower climbrate when in levelchange and acceleration is required - Do not engage alpha floor when over mach .6 or when TCAS is active or engine out and flap/slats extended - Adjusted layout of chrono in ND - Changed ordering of ils approach types in MCDU - LNAV fixes February 22 Release version 1.55b7 ================================== - Fuel pump lights should flash momentarily when pumps turned on - LNAV changes to allow more bypasses - LNAV fixes for CF legs and teardrop - Fixed issue where center pumps do not switch on when wing tanks have enough room - Fix wind not displayed in the air with gs < 100 - Move cancelled cautions to bottom of screen and display in white - Fixed approach VIA reset after each flightplan change - Revised representation of APU generator data on ECAM - Allow APU fire loop test to shut down apu February 8 Release version 1.55b6 ================================= - Fixed a crash in vnav - LNAV fixes - Added option to link only left + right QNH and leave ISIS independent - Fix managed climb pitch and F/D movement when transitioning from alt hold to climb - Fixed flaps/slats not showing failed state when engine is shut down - Prevent markers from extending into missed approach path if path not visible - Dot not box FMA V/S or FPA modes when target values change - Fixed INIT B zfw/cfg formatting - Added F/CTL and SFCS maintenance ECAM indications - Add input checks to transition altitude/level - perf approach transition level should be FL not ALT - Do not clear ICAO entries in weather request page when weather type switched - Fix exhaust/blower IOS check items January 31 Release version 1.55b4 ================================= - Added IAE engine fail ecam January 31 Release version 1.55b3 ================================= - NO NAV INTERCEPT message should reset when pulling HDG - Fixed PERF DES managed speed should update when new values entered - Fix for speedbrake/flap handle input issues January 28 Release version 1.55b2 ================================= - Hotfix for brakes issue January 26 Release version 1.55b1 ================================= - Fixed issue with T/D shifting after activating descend - Weather/terrain radar fixes February 17 Release version 1.54.1 ================================== - Fixed IAE engine failure ECAM January 28 Release version 1.54 =============================== Systems: - New usage based hydraulic model FMS: - FCU altitude should first jump to nearest one thousand if scale switched placed on 1000 and altitude is not a whole thousand value and alt selection rotated - Updated descend speeds - Only autotune ILS if destination is closer than 320 NM MCDU: - SEC PERF should only be available when SEC FPLN not empty - Added more checking to values entered in RADFIX page - Added rangecheck to PERF V speed entry - Added UTC/DIST to DIR TO page - PROG "UPDATE AT" should only be available if not GPS PRIMARY - PROG "UPDATE AT" will only modify received mixed irs signal and not affect adiru position - IRS INIT IRS positions should be green instead of cyan - Fixed some incorrect approach names Displays: - Only show ECAM maintenance items during FWC phase 1/10 (on ground) - Do not show end of descend markers if vertical mode is glideslope - Fixed alternate runway drawn even though alternate route is not drawn - Improved PFD Vprot marker on speed tape - Fixed arc terrain mask - Terrain Peak option reviewed - Draw FLS beam below route Autoflight: - Autopilot pitch stabilisation at lower speeds - Improved pitch stability during roll Hardware: - Support for CPFlight FCU, TRIM, WXR, ACP, ATC, BRT Misc: - Reversed blower/extract fan switches to be pushed in by default - Fixed glideslope beam off on some airports - Use scenery file DME position instead of navigraph reported position - Adjusted 833 exclusion for SAR frequency from [123.050, 123.150] to [123.075, 123.125] January 23 Release version 1.54b6 ================================= - Updated descend speeds January 21 Release version 1.54b5 ================================= - [Misc] Adjusted 833 exclusion for SAR frequency from [123.050, 123.150] to [123.075, 123.125] - Fixed crash in Prosim Display terrain rendering - Use scenery file DME position instead of navigraph reported position January 20 Release version 1.54b4 ================================= - Improved pitch stability during roll - Draw FLS beam below route - Support for CPFlight FCU, TRIM, WXR, ACP, ATC, BRT - CPFlight Overhead switches reviewed - Terrain Peak option reviewed - Fixed some incorrect approach names - Fixed glideslope beam off on some airports January 11 Release version 1.54b3 ================================= - Fixed some hydraulics issues in new hydraulics system - Autopilot pitch stabilisation at lower speeds - Fixed arc terrain mask January 8 Release version 1.54b2 ================================ - Improved PFD Vprot marker on speed tape - Fixed alternate runway drawn even though alternate route is not drawn - Reversed blower/extract fan switches to be pushed in by default January 6 Release version 1.54b1 ================================ - New usage based hydraulic model - SEC PERF should only be available when SEC FPLN not empty - Added more checking to values entered in RADFIX page - Only show ECAM maintenance items during FWC phase 1/10 (on ground) - FCU altitude should first jump to nearest one thousand if scale switched placed on 1000 and altitude is not a whole thousand value and alt selection rotated - Added rangecheck to PERF V speed entry - Added UTC/DIST to DIR TO page - PROG "UPDATE AT" should only be available if not GPS PRIMARY - PROG "UPDATE AT" will only modify received mixed irs signal and not affect adiru position - Do not show end of descend markers if vertical mode is glideslope - Only autotune ILS if destination is closer than 320 NM - IRS INIT IRS positions should be green instead of cyan December 27 Release version 1.53 ================================ Systems: - Added bird strike failure - Autotrim should not move trim wheel if G+Y unpowered - Fixed elevator trim not resetting on ground - Fixed gravity feed using crossfeed even when crossfeed valve is closed - Do not clear fault signal during FCC boot if failure active FMS: - Do not reengage alpha floor if disconnected through a/thr disconnect button - LVR ASYM should only show when engines are at or above idle - INIT B trip wind should not be writable when dashed - Updated CI tables - ND next waypoint information should skip abeam points after a direct to with abeam points - Round uplink wind altitude to 1000 feet - Disable A/THR if A/THR channel 2 is failed and dual cmd enabled - Fixed issues where holdings would change or disappear during TMPY FPLN modifications - Fixed FROM point in FPLN shows show time passed over instead of current time - Adjusted LOC pre-capture bank angle to capture localiser with an increased bank Flight guidance: - Adjusted LOC precapture radius for steeper interception - stabilized pitch F/D - New SRS takeoff implementation - Modified initial climb behavior of OPEN CLB Hardware: - Added delay for Skalarki CB's Displays: - Tuned various part of the PFD - Fixed status page reverts to previous page after 3 seconds when status is normal - Improved calculation of vnav arrows - Updated visibility mask for ND rose mode Misc: - Added option to switch between +1000 FT and +1500 FT for accel/thrust reduction altitude - Added support for new FS2020 modern flight models - Fixed scenery BGL layering during database build - Fixed wrong scenery path used when selecting older version of Prepar3D if newer version is installed - Fix webserver crash December 23 Release version 1.53b10 ================================== - Expose F/D tuning parameters to maintenance tuning page - Adjusted LOC pre-capture bank angle to capture localiser with an increased bank December 14 Release version 1.53b9 ================================== - Fix webserver crash December 13 Release version 1.53b8 ================================== - Fixed FROM point in FPLN shows show time passed over instead of current time - Fixed issues where holdings would change or disappear during TMPY FPLN modifications - Do not clear fault signal during FCC boot if failure active - Disable A/THR if A/THR channel 2 is failed and dual cmd enabled December 10 Release version 1.53b7 ================================== - Round uplink wind altitude to 1000 feet - Added delay for Skalarki CB's - Fixed wrong scenery path used when selecting older version of Prepar3D if newer version is installed December 7 Release version 1.53b6 ================================= - Updated visibility mask for ND rose mode - ND next waypoint information should skip abeam points after a direct to with abeam points December 5 Release version 1.53b5 ================================= - Modified initial climb behavior of OPEN CLB - Updated CI tables - Fixed gravity feed using crossfeed even when crossfeed valve is closed - INIT B trip wind should not be writable when dashed November 30 Release version 1.53b4 ================================== - Fixed elevator trim not resetting on ground November 29 Release version 1.53b3 ================================== - LVR ASYM should only show when engines are at or above idle - Improved calculation of vnav arrows - Fixed scenery BGL layering during database build November 25 Release version 1.53b2 ================================== - Autotrim should not move trim wheel if G+Y unpowered - New SRS takeoff implementation - stabilized pitch F/D November 19 Release version 1.53b1 ================================== - Added support for new FS2020 modern flight models - Fixed status page reverts to previous page after 3 seconds when status is normal - Do not reengage alpha floor if disconnected through a/thr disconnect button - Added option to switch between +1000 FT and +1500 FT for accel/thrust reduction altitude November 15 Release version 1.52 ================================ Displays: - Fixed efis PLAN mode missing selected map items - Fixed runways of SEC FPLN always displayed even when SEC FPLN not displayed - Optimization of terrain center sweep - Do not show flags on PFD/ND during light test - Fixed display terrain not showing in rose mode and 10nm range - Terrain annunciations temporary state for peak terrain calculation - Fixed terrain annunciation colors - Do not flash QNH value in PFD while aircraft is on the ground - Fixed draw terrain annunciation with ADIRS offline - Fixed lower terrain annunciation error - During non precision approach, show NPA scale in FMS approach phase, regardless of FMA mode (shown only when APPR button pushed previously) - Improved RDME distance readout - Speed change dot in ND is now dashed magenta - Tuned upper ECAM in IAE mode - Engine gauge should show double XX when no FADEC data available - Improved calculation of level off markers - Next altitude in alt tape now only shows altitudes where level off occurs - Altitude readout in PFD should show altitudes < 1000 feet in 3 digits - Blue level-off arrow in ND is now calculated based on FMA mode instead of FPA FMS: - Fixed speedrange not shown in speedtape during early descend until T/D reached - Fixed crash and other issues with holding at PPOS - Performance increase Hardware: - Fix for fscockpit printer panel backlight - [Drivers] Added new CPFlight V2 driver - [CPFlightV2] Added overhead support Systems: - Fixed ND Rose Mode terrain and weather limits - Fixed Terrain On ND switch logic Flight: - Autopilot tuning for alt capture - Increased roll control with only spoilers available - Adjusted working of automatic rudder control during manual flight - Improved FBW normal law pitch stability Misc: - Fixed SimConnect data errors - Fixed airworks altitude in ProSimIOS - Fixed SDK write to COM frequency 136.xxx - Fixed detached Map module got disabled when selecting Height Map in ProSimIOS - IAE engine fixes - Fixed shutdown all networked computers did not always work from ProSimIOS - Fixed storing display layout on certain systems in ProsimDisplay - Fixed ProSimIOS module auto update November 13 Release version 1.52b14 =================================== - Fixed SimConnect data errors - Fixed runways of SEC FPLN always displayed even when SEC FPLN not displayed - Fixed airworks altitude in ProSimIOS November 11 Release version 1.52b13 =================================== - Fixed speedrange not shown in speedtape during early descend until T/D reached - Optimization of terrain center sweep - Fixed crash and other issues with holding at PPOS - Do not show flags on PFD/ND during light test November 9 Release version 1.52b12 ================================== - Fixed crash November 8 Release version 1.52b11 ================================== - Fixed display terrain not showing in rose mode and 10nm range - Terrain annunciations temporary state for peak terrain calculation - Fixed terrain annunciation colors - Fixed SDK write to COM frequency 136.xxx - Do not flash QNH value in PFD while aircraft is on the ground - Performance increase November 4 Release version 1.52b10 ================================== - Fixed ND Rose Mode terrain and weather limits - Fixed Terrain On ND switch logic - Fixed draw terrain annuncionation with ADIRS offline November 3 Release version 1.52b9 ================================= - Terrain Sweep starting fix - Fixed lower terrain annunciation error - During non precision approach, show NPA scale in FMS approach phase,regardless of FMA mode (shown only when APPR button pushed previously) November 1 Release version 1.52b8 ================================= - Fix for fscockpit printer panel backlight - Fixed detached Map module got disabled when selecting Height Map in ProSimIOS - Improved RDME distance readout - Autopilot tuning for alt capture - Speed change dot in ND is now dashed magenta - Increased roll control with only spoilers available October 25 Release version 1.52b7 ================================= - Adjusted working of automatic rudder control during manual flight - IAE engine fixes October 22 Release version 1.52b6 ================================= - Fixed shutdown all networked computers did not always work from ProSimIOS - Tuned upper ECAM in IAE mode October 21 Release version 1.52b5 ================================= - Fix crashing issue October 20 Release version 1.52b4 ================================= - [Drivers] Added new CPFlight V2 driver - [CPFlightV2] Added overhead support - Engine gauge should show double XX when no FADEC data available October 19 Release version 1.52b3 ================================= - Fixed storing display layout on certain systems in ProsimDisplay - Improved calculation of level off markers - Next altitude in alt tape now only shows altitudes where level off occurs October 15 Release version 1.52b2 ================================= - Altitude readout in PFD should show altitudes < 1000 feet in 3 digits - Blue level-off arrow in ND is now calculated based on FMA mode instead of FPA - Fixed ProSimIOS module auto update October 11 Release version 1.52b1 ================================= - Improved FBW normal law pitch stability October 11 Release version 1.51 =============================== Flight: - Slight FBW normal law improvements Displays: - Fixed ND mask too large at bottom of ND - Fixed navigation data to go below airplane symbol and above terrain/Weather info - Improved terrain rendering and implemented center sweep effect - Fixed terrain brightness - Fixed E/D, T/C extending being LNAV intercept path when intercepting FMS: - Base uplink winds on opt alt and use better altitude steps for layers - Added support for FLS non standard approach gradients - Always add implicit 1500 feet altitude waypoint after runway if no SID selected - Prevent steep path indication when next segment is a decel leg - For non precision approaches, do not activate FINAL before approach part of the flight plan - Leave managed mode on FCU alt restriction instead of maintaining navvertical in fcu alt lock mode Misc: - Fixed magnetic variation not always correctly considered during heading display on ProSimIOS - Remove weather information when both terrain active and Peaks Option is off - Fixed ProSimIOS now closes automatically when Windows shuts down also when no connection to ProSimSystem. - Fixed Active Sky real-time weather deactivated after reposition with ProSimIOS - Improved cloud definition in ProSimIOS now always AGL (requires rebuild of ProSimSystem database) - Fixed existent triggered failures not shown on ProSimIOS when ProSimSystem was started first - Fix excessive CPU load Note: This release includes a rework of the terrain rendering. There are some beta users reporting differences between CPT/FO NDs which we could not reproduce so far. Please create a support ticket if you can reproduce it with this release. October 8 Release version 1.51b8 ================================ - Tuned F/D and go around pitch control October 7 Release version 1.51b7 ================================ - Improved protection for cabin overpressurize when pressurisation is in auto mode - Fixed autopilot response during landing/go around - Fixed ND mask too large at bottom of ND October 1 Release version 1.51b6 ================================ - Fixed magnetic variation not always correctly considered during heading display on ProSimIOS - Fixed issues with black region on ND display September 27 Release version 1.51b5 =================================== - Base uplink winds on opt alt and use better altitude steps for layers - Remove weather information when both terrain active and Peaks Option is off - Fixed navigation data to go below airplane symbol and above terrain/Weather info - Fixed terrain brightness September 23 Release version 1.51b4 =================================== - Improved terrain rendering and implemented center sweep efect - Fixed ProSimIOS now closes automatically when Windows shuts down also when no connection to ProSimSystem. - Tuned autopilot - Added support for FLS non standard approach gradients September 20 Release version 1.51b3 =================================== - Improved cloud definition in ProSimIOS now always AGL (requires rebuild of ProSimSystem database) - Fixed Active Sky real-time weather deactivated after reposition with ProSimIOS - Always add implicit 1500 feet altitude waypoint after runway if no SID selected September 13 Release version 1.51b2 =================================== - Prevent speed path indication when next segment is a decel leg - Fix excessive CPU load September 8 Release version 1.51b1 ================================== - Slight FBW normal law improvements - For non precision approaches, do not activate FINAL before approach part of the flight plan - Leave managed mode on FCU alt restriction instead of maintaining navvertical in fcu alt lock mode - Fixed E/D, T/C extending being LNAV intercept path when intercepting - Fixed existent triggered failures not shown on ProSimIOS when ProSimSystem was started first September 3 Release version 1.50 ================================ Flight guidance: - Tuned ALT* capture FMS: - Improved CPDLC position report FMS prefill - Fixed abeam points not showing up for direct to with abeam points - Fixed issue when pulling V/S during descend - DES PERF page should only show managed speed parts in large font that have been changed - PERF page should show actual first managed target speed while on the ground - Fixed VNAV above-alt constraint before T/D causes early descend Systems: - Fixed single ecam mode with unpowered ECP should not switch lower display to ECAM when holding ECAM button - Reduced thrust threshold for automatic spoiler retraction after landing - If STS page shows after ECAM sequence, also light STS light and allow clearing by pressing STS Displays: - Improved cyan color of ND descend/climb markers Hardware: - Fix FSC MCDU display issue where blank screen appears instead of normal display Audio: - Improved many cockpit sounds Misc: - Fixed prosim display crash on startup of upper ECAM display August 31 Release version 1.50b5 ================================ - Improved CPDLC position report FMS prefill - Fixed prosim display crash on startup of upper ECAM display August 20 Release version 1.50b4 ================================ - Fixed abeam points not showing up for direct to with abeam points - Improved cyan color of ND descend/climb markers - Tuned ALT* capture August 24 Release version 1.50b3 ================================ - Reduced thrust threshold for automatic spoiler retraction after landing - Fixed issue when pulling V/S during descend August 20 Release version 1.50b2 ================================ - Fixed crash August 19 Release version 1.50b1 ================================ - DES PERF page should only show managed speed parts in large font that have been changed - If STS page shows after ECAM sequence, also light STS light and allow clearing by pressing STS - PERF page should show actual first managed target speed while on the ground - Fixed VNAV above-alt constraint before T/D causes early descend - Fix FSC display issue where blank screen appears instead of normal display - CPDLC through Hoppie network added. This is the first iteration and not yet complete. Add Hoppie logon code to Datalink configuration menu to use. August 6 Release version 1.49 ============================= FMS: - Added FMA approach capabilities for FLS approaches - Fix FLS magdev issues - Revised logic for arming/engaging RNAV approaches - Split Takeoff and GO thrust reduction/accelt/eo accel fields - Do not flash LVR CLB during A FLOOR or TOGA LK - LNAV/VNAV fixes - Fixed descend speed limit not retained in some cases Flight guidance: - Autoretract slats when slats were locked in alphalock function and flap handle is in up state and alpha lock nolonger applies - Handle reversion from open des to V/S if FCU altitude increased above current altitude - Limit roll authority when roll flightcontrol surfaces are inoperational - Tuned speedbrake effect to Vls at higher altitudes Displays: - Added E/WD A-LOCK indication - Center Align SD ELEC page APU and EXT PWR data - ECAM AUTO/FLT should be named AUTO FLT - Always draw navaid route waypoints as diamonds, unless they are actually tuned or selected on the EFIS panel - Removed PFD/ND FCU speed and alt smoothing - PFD FCU Alt should show in blue when FINAL mode is active - Only show vnav intercept marker while descending - Only show ND route dashed when active mode is TRK/HDG - Do not show decel markers in missed approach path Systems: - Redefined cargo fire test sequencing - Fixed brake hydraulics affected by leak measurement valves - Added springload to hot air valve to prevent valve disagree - Only allow DECEL light when autobrake is active - Pressing active switch on RMP should not cancel active selection - Improvements in ECAM HYD synoptics - Fixed ECAM F/CTRL page hyd indications when Leak Measurement valves closed - Use origin airport altitude as CPC abort altitude - Fixed incorrect EGPWS callout near destination runway MCDU: - Limit APPR VDEV number to -9999 to +9999 - Allow any of "NO", "NODH" or "NO DH" to indicate No Da in PERF APPR page - Fixed VERT REV page should not return to FPLN when entering alt or speed restriction - Changing default speed limit in VERT REV page should stay on VERT REV page - Allow CLR on default speed limit to remove limit - Change APPR PERF MDA/DH label to BARO/RADIO - Round MCDU optimum alt to nearest 1000 - DES Winds should be sorted in reverse in DESCENT WIND page Hardware: - Fixes for FSC MCDU - Fixed cockpit sonic master warning/caution/sidestick priority lights Misc: - Do not force ILS radio tuning on reposition - Also close ProSimIOS and shutdown IOS computer when network shutdown all command is used. - Fix spurious activation of dontSink when repositioning from ground to 3NM final - Fixed simulator Active Sky status no longer continuously refreshing without actual update - Fix airport/runway lookup where runway had a L/C/R identifier but installed scenery is not, causing lookup to fail - Fixed some recording parameters could not be imported/exported with ProSimIOS - Sidestick reversal failure split up in reversal roll and pitch August 2 Release version 1.49b8 =============================== - Fixed incorrect EGPWS callout near destination runway - Use origin airport altitude as CPC abort altitude - Fixed descend speed limit not retained in some cases - LNAV/VNAV fixes - Do not show decel markers in missed approach path July 26 Release version 1.49b7 ============================== - Only show ND route dashed when active mode is TRK/HDG - Only show vnav intercept marker while descending - PFD FCU Alt should show in blue when FINAL mode is active - Fixed ECAM F/CTRL page hyd indications when Leak Measurement valves closed - Sidestick reversal failure split up in reversal roll and pitch - Removed PFD/ND FCU speed and alt smoothing - Always draw navaid route waypoints as diamonds, unless they are actually tuned or selected on the EFIS panel - Improvements in ECAM HYD synoptics - DES Winds should be sorted in reverse in DESCENT WIND page - Fixes for FSC MCDU July 16 Release version 1.49b6 ============================== - Pressing active switch on RMP should not cancel active selection - Only allow DECEL light when autobrake is active - Tuned speedbrake effect to Vls at higher altitudes - Limit roll authority when roll flightcontrol surfaces are inoperational - Round MCDU optimum alt to nearest 1000 - Do not flash LVR CLB during A FLOOR or TOGA LK - ECAM AUTO/FLT should be named AUTO FLT - Change APPR PERF MDA/DH label to BARO/RADIO - Split Takeoff and GO thrust reduction/accelt/eo accel fields - Fixed cockpit sonic master warning/caution/sidestick priority lights July 9 Release version 1.49b5 ============================= - Allow CLR on default speed limit to remove - Changing default speed limit in VERT REV page should stay on VERT REV page - Handle reversion from open des to V/S if FCU altitude increased above current - Fixed some recording parameters could not be imported/exported with ProSimIOS - Fix airport/runway lookup where runway had a L/C/R identifier but installed scenery is not, causing lookup to fail July 7 Release version 1.49b4 ============================= - Fixed VERT REV page should not return to FPLN when entering alt or speed restriction - Allow any of "NO", "NODH" or "NO DH" to indicate No Da in PERF APPR page - Center Align SD ELEC page APU and EXT PWR data - Revised logic for arming/engaging RNAV approaches - Limit APPR VDEV number to -9999 to +9999 - Autoretract slats when slats were locked in alphalock function and flap handle is in up state and alpha lock nolonger applies - Added springload to hot air valve to prevent valve disagree July 1 Release version 1.49b3 ============================= - Added E/WD A-LOCK indication - Fixed simulator Active Sky status no longer continuously refreshing without actual update - Fix spurious activation of dontSink when repositioning from ground to 3NM final June 25 Release version 1.49b2 ============================== - Fix spurious activation of dontSink when repositioning from ground to 3NM final - Fixed brake hydraulics affected by leak measurement valves - Also close ProSimIOS and shutdown IOS computer when network shutdown all command is used. - Fix FLS magdev issues June 20 Release version 1.49b1 ============================== - Added FMA approach capabilities for FLS approaches - Do not force ILS radio tuning on reposition - Redefined cargo fire test sequencing June 17 Release version 1.48 ============================ Systems: - Fixed APU ECB target N1 should be 99% based on bleed demand - Tuned bleed air demand of air starter to allow more realistic N1 requirements for cross bleed start - Improved N1/N2 parameters when windmilling - Fixed engine parameter input to FWC when EIU/FADEC fails Flight guidance: - Tuned clb mode to better maintain speed when activated FMS: - Added FLS approach type option (beta). This can be switched on as an option and will replace the regular APP NAV with F-LOC and F-G/S modes. - Do not command F speed if flaps is set to 3 during flaps 3 approach - For block altitude constraints, target conflicting altitude (either the lower of higher limit) instead of always the lowest altitude to build vnav path - Added shallow segments in vnav path where larger speed reductions are needed due to constraints during descend - Fixed display and processing of managed speed in DES PERF page Displays: - Refined logic for when ND renders white SEC FPLN and when it is not visible - Reworked marker indication in PFD Hardware: - Added standby speed gauge - Added configurable gates for engine failures - Improvement in processing time of hardware input/output - Renamed S_CDU1_KEY_FLPN to S_CDU1_KEY_FPLN and S_CDU2_KEY_FLPN to S_CDU2_KEY_FPLN Misc: - Added close all prompt to close all doors in MCDU MAINT DOORS page - Adjusted ground fuel flow for idle N1 - Add support for 2021 PBR flight model - Fixed overriding real-time Active Sky weather after position change by ProSimIOS - Fixed temperature and dew point not shown in AOC weather request when Active Sky is used - Fixed FS2020 COM frequency setting - Fix for FS2020 engine starting issues June 14 Release version 1.48b8 ============================== - Added FLS approach type option - Fixed renaming issue with MCDU FPLN keys June 10 Release version 1.48b7 ============================== - Fixed overriding real-time Active Sky weather after position change by ProSimIOS - Do not command F speed if flaps is set to 3 during flaps 3 approach - For block altitude constraints, target conflicting altitude (either the lower of higher limit) instead of always the lowest altitude to build vnav path - Add support for 2021 PBR flight model June 3 Release version 1.48b6 ============================= - Fixed switch synchronisation issues June 2 Release version 1.48b5 ============================= - Fixed temperature and dew point not shown in AOC weather request when Active Sky is used - Fixed APU ECB target N1 should be 99% based on bleed demand - Adjusted ground fuel flow for idle N1 - Refined logic for when ND renders white SEC FPLN and when it is not visible - Fixed display and processing of managed speed in DES PERF page - Tuned clb mode to better maintain speed when activated - Tuned bleed air demand of air starter to allow more realistic N1 requirements for cross bleed start May 25 Release version 1.48b4 ============================= - Added standby speed gauge - Added close all prompt to close all doors in MCDU MAINT DOORS page - Added configurable gates for engine failures - Improved N2 parameters when windmilling - Fixed engine parameter input to FWC when EIU/FADEC fails May 24 Release version 1.48b3 ============================= - Reworked marker indication in PFD - Improvement in processing time of hardware input/output May 20 Release version 1.48b2 ============================= - Fixed FS2020 COM frequency setting - Fix n1/n2 indications on windmilling engine May 18 Release version 1.48b1 ============================= - Fix for FS2020 engine starting issues May 17 Release version 1.47 =========================== - Hotfix 1.46.1 release required to be installed to update to version 1.47 and above. Before updating to version 1.47 or higher from version 1.46 and below, please install the hotfix 1.46.1 first. Otherwise the update will fail with error message 'Unable to update: Required file ProSimA320-System AND ProSim320.zip not found in downloaded file.' Misc: - Change internal product name to generic A322 - Shutdown all option now available in ProSimIOS also without any network computers configured - ProSimIOS now also uses other ProSim modules for shutdown all computers command - Renamed MCP labeled elements to FCU - Added support for GSX pushback system FMS: - When goaround initiated with FCU altitude below A/C altitude, engage SRS mode instead of V/S - Do not allow PERF APPR DH entry if no precision vertical guidance available - Adjusted FMS restring logic so holdings are retained and included when restringing Flight: - When transitioning from alternate law to direct law because of gear down and THS unpowered or jammed, store mean elevator position and use that as sidestick neutral position Systems: - Added FCDC faults Navigation: - Fixed missing marker data Hardware: - Make landing elevation alt available to calibrate for Skalarki hardware - Added support for door switches/indicators in Poldragonet Trim/Door panel - Reduce EHID MCDU screen writes May 12 Release version 1.47b6 ============================= - Added simulator flap/slat degrees in SDK May 11 Release version 1.47b5 ============================= - When goaround initiated with FCU altitude below A/C altitude, engage SRS mode instead of V/S - Do not allow PERF APPR DH entry if no precision vertical guidance available - Adjusted FMS restring logic so holdings are retained and included when restringing - Change internal product name to generic A322 May 3 Release version 1.47b4 ============================ - Fixed missing marker data - Make landing elevation alt available to calibrate for Skalarki hardware - Shutdown all option now available in ProSimIOS also without any network computers configured - Add support for updating to 1.47b5 and above. Before updating to version 1.47b5 or higher from version 1.47b3 and below, please install this version first (just prior to the update to 1.47b5 and above). Otherwise the upgrade will fail with error message 'Unable to update: Required file ProSimA320-System AND ProSim320.zip not found in downloaded file.' April 26 Release version 1.47b3 =============================== - Added support for door switches/indicators in Poldragonet Trim/Door panel - Reduce EHID MCDU screen writes - ProSimIOS now also uses other ProSim modules for shutdown all computers command April 22 Release version 1.47b2 =============================== - Added FCDC faults - Renamed MCP labeled elements to FCU April 19 Release version 1.47b1 =============================== - When transitioning from alternate law to direct law because of gear down and THS unpowered or jammed, store mean elevator position and use that as sidestick neutral position - Added support for GSX pushback system May 03 Release version 1.46.1 ============================= - Hotfix release required to be installed to upgrade to version 1.47 and above. Before updating to version 1.47 or higher from version 1.46 and below, please install this hotfix first. Otherwise the upgrade will fail with error message 'Unable to update: Required file ProSimA320-System AND ProSim320.zip not found in downloaded file.' April 16 Release version 1.46 ============================= Systems: - Do not show yellow elec pump light if pump is on because of cargo door operation - Flaps/slats are operational when LMV's are closed - Added engine failure with damage - Added circuitbreakers and circuitry for reverser shutoff valve solenoids - Inhibit F/D on dual ADR failure - Improved charge cycle of batteries - Fix error in ECAM sheets preventing "10" callout - Added tyre pressure failures FMS: - Do not show alt cstr in alt tape when FINAL mode is active - If speed is dashed and speed dial turned, use current speed as value Displays: - Alt tape should not be available when backup speed system is active while GPS is offline - Only show S and F markers in speedtape in flight - Fixed VOR deflection should be 5 degrees per dot - Tuned speedtape Vls, Valphaprot and speedbug shape/size Hardware: - Added PFD/ND XFER button to configuration screen "switch type" list so they can be configured as latched switches - Added FDS Ethernet driver Misc: - Fixed looping relay sounds in certain conditions - Mute ProsimAudio sounds only during pause and not during freeze to prevent GSX pushback from muting prosim audio - Implemented new VATSIM data format to allow VATSIM information displayed on ProSimIOS map again - Fixed airspaces not shown on ProSimIOS map (needs new database build) April 14 Release version 1.46b7 =============================== - Mute ProsimAudio sounds only during pause and not during freeze to prevent GSX pushback from muting prosim audio - Fix error in ECAM sheets preventing "10" callout - Fix for brakes not working since 1.46b6 April 12 Release version 1.46b6 =============================== - Implemented new VATSIM data format to allow VATSIM information displayed on ProSimIOS map again - Fixed airspaces not shown on ProSimIOS map (needs new database build) April 6 Release version 1.46b5 ============================== - More updates to speed tape - Added tyre pressure failures - Added PFD/ND XFER button to configuration screen "switch type" list so they can be configured as latched switches March 29 Release version 1.46b4 =============================== - Tuned speedtape Vls, Valphaprot and speedbug shape/size - Improved charge cycle of batteries - Fixed VOR deflection should be 5 degrees per dot - Do not show alt cstr in alt tape when FINAL mode is active March 28 Release version 1.46b3 =============================== - Inhibit F/D on dual ADR failure - Only show S and F markers in speedtape in flight - Added circuitbreakers and circuitry for reverser shutoff valve solenoids - Fixed looping relay sounds in certain conditions - Alt tape should not be available when backup speed system is active while GPS is offline March 24 Release version 1.46b2 =============================== - Added engine failure with damage - Flaps/slats are operational when LMV's are closed - Do not show yellow elec pump light if pump is on because of cargo door operation March 22 Release version 1.46b1 =============================== - Added FDS Ethernet driver March 19 Release version 1.45 ============================= Systems: - Updated pack ram air valve logic - Allow thrust reverser to use HP line as power source Displays: - Do not display n1 limit value when n1 mode is MREV - Round vsi digital round out instead of truncate it FMS: - Do not reset FMA during unusual attitudes MCDU: - Fixed lat/lon formatter issue with negative lat/lon in MCDU INIT page Hardware: - Fixed an issue where Poldragonet C/B would keep popping out if manually pulled out and pushed back in. - Added support for Poldragonet CLS device Misc: - Fixed inner marker received on MKR radio when power is off - Fixed failures active before ProSimIOS connected were not shown as active. - Add FCU/EFIS light test for Skalarki and ProsimDisplay - Added experimental isa deviation based altitude lapse rate compensation - Make sure GPWS Don't Sink does not rearm after repositioning to the air. - Fix altitude readout to take height of static port into account - Retract ground spoilers when aircraft becomes airborne (repositioning) with ground spoilers still deployed. - Make sure GPWS Don't Sink is not armed after repositioning to the air. - Filter environmental temperature data to prevent incorrect data from simulator - Added facility for generating debug log file March 19 Release version 1.45b9 =============================== - Do not display n1 limit value when n1 mode is MREV - Fixed inner marker received on MKR radio when power is off March 5 Release version 1.45b8 ============================== - Fixed failures active before ProSimIOS connected were not shown as active. - Round vsi digital round out instead of truncate it - Updated pack ram air valve logic - Fixed lat/lon formatter issue with negative lat/lon in MCDU INIT page - Add FCU/EFIS light test for Skalarki and ProsimDisplay March 2 Release version 1.45b7 ============================== - Added experimental isa deviation based altitude lapse rate compensation March 1 Release version 1.45b6 ============================== - Fixed an issue where Poldragonet C/B would keep popping out if manually pulled out and pushed back in. - Added support for Poldragonet CLS device February 25 Release version 1.45b5 ================================== - Make sure GPWS Don't Sink does not rearm after repositioning to the air. February 25 Release version 1.45b4 ================================== - Fix altitude readout to take height of static port into account February 25 Release version 1.45b3 ================================== - Retract ground spoilers when aircraft becomes airborne (repositioning) with ground spoilers still deployed. - Make sure GPWS Don't Sink is not armed after repositioning to the air. February 25 Release version 1.45b2 ================================== - Do not reset FMA during unusual attitudes - Allow thrust reverser to use HP line as power source February 22 Release version 1.45b1 ================================== - Filter environmental temperature data to prevent incorrect data from simulator February 22 Release version 1.44.1 ================================== FMS: - Fixed engine out managed speed stuck at green dot during approach - Allow direct entry of speed/alt constraint in FPLN page - Replaced offset code - Update to dep/arr latrev pages to show transitions after selecting approach/departure without needing to scroll up Systems: - Fixed fuel flow calculation causing high fuel consumption calculation - Added AC Ess feed faults - Improved handling of dual channel flap/slat failures - Added failures for individual SFCC flap and slat channels - ALT RPTG off should inhibit TCAS - Fixed TA ONLY not appearing when mode switch set to TA - Fixed issues with triple click audio after A/P disconnect - Enabled HF radios - Fixed vprot max speed stripes should not be visible while in direct law or alternate law without protections - Fixed pitch mechanical reversion should not show alternate law in ECAM - Added ATSU ECAM procedures - Added ATSU MCDU pages - Update VHF3 RMP control - TCAS targets are now visible on ground when TCAS is in AUTO mode - Yellow ELEC pump indicator will now light when pump was activated due to cargo door request - Simulate automatic control of yellow elec pump due to cargo door usage - Set default XPDR code to 2000 - Fan air optimized to allow better triggering of bleed low air failure - Added cockpit door controls - N1 engine limits are reduced by anti ice demand - N1 is now affected by high bleed demand - Added navaid decoding simulation to radios Displays: - T/D should be blue if RNAV APP mode is armed - Do not show ND RANGE CHANGE message when map not available Flight dynamics: - Fixed upwards aileron range should be limited when aileron droop function is active - Added aileron undroop function - Fix automatic pitch increase at high AOA flight Hardware: - Fix FScockpit RMP charset mapping - FSCockpit RMP 3 backlight connected to overhead backlight - Updated skalarki libraries - Improved ProSimAudio WASAPI compatibility Misc: - Added support simbrief fuel/weight loading - Fixed radio's not writable through SDK in system.analog.R_xxxx - Fixed report VATSIM/IVAO Mode C only if ALT RPTG is ON - Fixed automated VATSIM/IVAO Mode C state change when getting airborne or after landing - Fixed SDK write to ADF not working - Added radio datarefs - Fixed VOR/ILS SDK course writing - Added support to exchange simulator weather information directly with Active Sky (enable in ProSimSystem config) - Added option to configure Active Sky AppData path - Fixed XPDR display does not correctly show leading 0's during editing - Fix SSL connection to aviationweather - Updated ice model - Fix VATSIM/IVAO/PilotEdge clients not shown on ProSimIOS map - Added community scenery import for FS2020 - Fixed P3D V4 nose wheel steering issue - Tuned deicing time - Fixed fire test activating visual model fire - Added brake fan gates and SDK access February 19 Release version 1.44b33 =================================== - FS2020 normal flight model internal testing February 18 Release version 1.44b32 =================================== - Added navaid decoding simulation to radios February 17 Release version 1.44b31 =================================== - New engine bleed demand effects - Added cockpit door controls February 16 Release version 1.44b30 =================================== - Fixed fire test activating visual model fire - Do not show ND RANGE CHANGE message when map not available - Improved ProSimAudio WASAPI compatibility February 15 Release version 1.44b29 =================================== - Added brake fan gates and SDK access - T/D should be blue if RNAV APP mode is armed - Fan air optimized to allow better triggering of bleed low air failure February 14 Release version 1.44b28 =================================== - Update to dep/arr latrev pages to show transitions after selecting approach/departure without needing to scroll up February 9 Release version 1.44b27 ================================== - Tuned deicing time - Fix automatic pitch increase at high AOA flight February 5 Release version 1.44b26 ================================== - Fixed P3D V4 nose wheel steering issue - Replaced offset code February 5 Release version 1.44b25 ================================== - Added community scenery import for FS2020 - N1 is now affected by high bleed demand - N1 engine limits are reduced by anti ice demand January 28 Release version 1.44b24 ================================== - Allow direct entry of speed/alt constraint in FPLN page - Fix VATSIM/IVAO/PilotEdge clients not shown on ProSimIOS map - Updated ice model January 28 Release version 1.44b23 ================================== - Fix SSL connection to aviationweather January 28 Release version 1.44b22 ================================== - Added logging for AOC weather request - Fixed XPDR display does not correctly show leading 0's during editing - Set default XPDR code to 2000 January 26 Release version 1.44b21 ================================== - Better C/B synchronisation control January 26 Release version 1.44b20 ================================== - Allow IOS C/B manipulation to bypass timers January 26 Release version 1.44b19 ================================== - Delay C/B retrigger after IOS resets C/B failure January 26 Release version 1.44b18 ================================== - Add cooldown for hardware to pop C/B's after triggering in IOS - Added option to configure Active Sky AppData path - Improvements to Active Sky API requests January 25 Release version 1.44b17 ================================== - Updated skalarki libraries - Added aileron undroop function January 23 Release version 1.44b16 ====================================== - Added support to exchange simulator weather information directly with Active Sky (enable in ProSimSystem config) January 21 Release version 1.44b15 ====================================== - Fix RMP standby display in DATA mode January 20 Release version 1.44b14 ================================== - Yellow ELEC pump indicator will now light when pump was activated due to cargo door request - FSCockpit RMP 3 backlight connected to overhead backlight - TCAS targets are now visible on ground when TCAS is in AUTO mode January 19 Release version 1.44b13 ================================== - Fix FScockpit RMP charset mapping January 19 Release version 1.44b12 ================================== - Added ATSU data mode page - Added ATSU VHF3 scan masks - Changed DATA mode display on FSCockpit RMP to dashes - Fixed VOR/ILS SDK course writing January 17 Release version 1.44b11 ================================== - Added ATSU ECAM procedures - Added ATSU MCDU pages January 16 Release version 1.44b10 ================================== - Update VHF3 RMP control January 15 Release version 1.44b9 ================================= - Use 6 charactes for DATA label January 15 Release version 1.44b8 ================================= - Added radio datarefs January 15 Release version 1.44b7 ================================= - Fixed RMP update issues in skalarki/fscockpit hardware January 15 Release version 1.44b6 ================================= - Use 'S' character instead of 'A' for skalarki hardware - Simulate automatic control of yellow elec pump due to cargo door usage January 14 Release version 1.44b5 ================================= - Fixed upwards aileron range should be limited when aileron droop function is active - Fixed pitch mechanical reversion should not show alternate law in ECAM - Fixed vprot max speed stripes should not be visible while in direct law or alternate law without protections - Fixed SDK write to ADF not working - Added VHF3 data mode - Enabled HF radios - Added HF AM mode January 11 Release version 1.44b4 ================================= - Fixed automated VATSIM/IVAO Mode C state change when getting airborne or after landing January 8 Release version 1.44b3 ================================ - Fixed issues with tripcle click audio after A/P disconnect - Engine out managed speed stuck at green dot during approach January 6 Release version 1.44b2 ================================ - Fixed TA ONLY not appearing when mode switch set to TA - ALT RPTG off should inhibit TCAS - Added failures for individual SFCC flap and slat channels - Improved handling of dual channel flap/slat failures - Added AC Ess feed faults - Fixed report VATSIM/IVAO Mode C only if ALT RPTG is ON - Fixed radio's not writable through SDK in system.analog.R_xxxx December 31 Release version 1.44b1 ================================== - Fixed fuel flow calculation causing high fuel consumption calculation - Added support simbrief fuel/weight loading December 28 Release version 1.43 ================================ This release adds support for AOC (datalink from external applications). Initially, simbrief for flightplans and wind is supported and metar/taf can be requested from online sources. To use simbrief, enter your pilot ID (That is your simbrief pilot number, not the login name) in the ProsimA322-system configuration screen in the datalink tab. After configuring your pilot ID, INIT REQ and WIND REQ prompts will appear in the MCDU. Weather requests are available through the new ATSU subsystem accessible from the main menu in the MCDU. Furthermore, new visual models have been released for p3d and FS2020 which now support accurate modeling of the movement of flight control surfaces. Flight dynamics: - Asymetric elevator extention will now result in rolling behavior FMS: - Improve THR LK target N1 - Fixed crash when using stepalts - Improved handling of wind data through MCDU and AOC uplink MCDU: - Fix incorrect MCDU response when LSK pressed while message is shown in scratchpad December 26 Release version 1.43b17 =================================== - Add support for TAF to ATSU weather request December 24 Release version 1.43b16 =================================== - Prevent ECAM messages in FS2020 during engine start - Added asymetric elevator pitch adjustment December 22 Release version 1.43b15 =================================== - Added aviationweather.gov metar AOC interface - Added Datalink cockpit setup tab to allow configuration preference for datalink services - Added asymetric elevator panel dynamics December 18 Release version 1.43b14 =================================== - Updated kinematics for all spoiler surfaces December 18 Release version 1.43b13 =================================== - Enable ATSU MCDU subsystem - Synchronize external animations with simulator framerate December 17 Release version 1.43b12 =================================== - Improve THR LK target N1 - Fixed crash in ATC COMM key December 17 Release version 1.43b11 =================================== - Fixed ProSimDisplay exception with terrain mode and Direct2D December 17 Release version 1.43b10 =================================== - Added AOC weather request - Changes to lights in FS2020 model December 14 Release version 1.43b9 ================================== - Added support for AOC ALTN FPLN - Fixed crash when using stepalts December 13 Release version 1.43b8 ================================== - Correctly handle simbrief flightplan errors due to AIRAC mismatch December 13 Release version 1.43b7 ================================== - Fixed CI and FL not uplinking into ACT FPLN when AOC FPLN message received December 11 Release version 1.43b6 ================================== - Fix incorrect MCDU response when LSK pressed while message is shown in scratchpad - Tuned FS2020 normal law pitch behavior December 9 Release version 1.43b5 ================================= - Added ATSU - Improved handling of wind data through MCDU and AOC uplink December 6 Release version 1.43b4 ================================= - Simbrief AOC wind data added December 4 Release version 1.43b3 ================================= - Fix engine start problem December 4 Release version 1.43b2 ================================= - Initial test with Simbrief AOC integration. To use, set simbrief pilot id in ProsimSystem configuration screen -> datalink tab November 30 Release version 1.43b1 ================================== - Added new ProSimIOS November 26 Release version 1.42 ================================ This release mostly focuses on FS2020 integration. Systems: - L/R tank pump 1 and REV 2 should be inop during dc ess fault Misc: - Fixed ProSimDisplay shows black screen for certain configurations - Fixed whole database build no longer aborts in case of a data record import error from the navigation data November 25 Release version 1.42b4 ================================== - Fixed ProSimDisplay shows black screen for certain configurations November 23 Release version 1.42b3 ================================== - Improved database import speed November 17 Release version 1.42b2 ============-===================== - Fixed whole database build no longer aborts in case of a data record import error from the navigation data November 11 Release version 1.42b1 ============-===================== - L/R tank pump 1 and REV 2 should be inop during dc ess fault October 30 Release version 1.41 =============================== FMS: - New FMS fuel prediction model to increase reliability of fuel calculations Flight: - Improved alternate law pitch control and low speed stability Systems: - Increased size of fanair heat exchanger to increase bleed air lo temp failure effectiveness - Set powersource of fuel pump indicators to AC essential - Improvement to logic for FUEL CONSUMPT INCRSD ECAM message - Fixed secondary ECAM failure AIR COND label and fixed issue where it called up a blank screen - Added Secondary F/CTL failure - Fixed ACP 3 connected to wrong bus - Allow zone controller to work when AC power available - Static port will now issue failure when not powered - Cab fans will now issue failure when not powered - Fixed vent extract fan connected to dc essential bus instead of dc essential shed bus - Fixed Galley fan CTL power connected to wrong bus - Fixed crew oxygen valve to remain in current position when power is lost Hardware: - Added support for FScockpit MCDU brightness keys Misc: - Added gates for AC power up (any AC source), AC power down and ground power connect - Switched CB logic to trigger software CB software failure in IOS whenever CB gets pulled October 25 Release version 1.41b6 ================================= - New FMS fuel mode to increase reliability of fuel calculations - Improved alternate law pitch control and low speed stability October 20 Release version 1.41b5 ================================= - Fix manual braking issue October 20 Release version 1.41b4 ================================= - Added gates for AC power up (any AC source), AC power down and ground power connect - Switched CB logic to trigger software CB software failure in IOS whenever CB gets pulled October 18 Release version 1.41b3 ================================= - Increased size of fanair heat exchanger to increase bleed air lo temp failure effectiveness - Set powersource of fuel pump indicators to AC essential October 14 Release version 1.41b2 ================================= - Added support for FScockpit MCDU brightness keys - Improvement to logic for FUEL CONSUMPT INCRSD ECAM message - Fixed secondary ECAM failure AIR COND label and fixed issue where it called up a blank screen - Added Secondary F/CTL failure - Fixed ACP 3 connected to wrong bus - Allow zone controlled to work when AC power available - Static port will now issue failure when not powered - Cab fans will now issue failure when not powered - Fixed vent extract fan connected to dc essential bus instead of dc essential shed bus - Fixed Galley fan CTL power connected to wrong bus October 8 Release version 1.41b1 ================================ - Fixed crew oxygen valve to remain in current position when power is lost October 2 Release version 1.40 ============================== Systems: - Added rate limiter to nose wheel rotation speed - Changed LGCIU 1 ground/air relay to allow taking power from DC SVC bus when DC ESS is lost - Fixed power spike in DC essential bus causes tripping of A/THR - Updated ECAM ALL button logic - Fix FMS data source did not switch when ATT/HDG switch is used - Only autoextinguish APU fire if fire occured while on the ground - Fixed switching off FAC 1+2 should inop A/THR - Fixed FAC resetable fault does not resolve when resetting FAC - Fixes for too low terrain warning during landing - Added CB's for audio control panels - Refined LGCIU signal 10 for gear release solenoid - Added Flood lt main center panel output left and Flood lt main center panel output right to control indivual MIP center flood lights - Added Flood lt pedestal output left and Flood lt pedestal output right outputs to control individual lamps inside the pedestal flood light - Added boot sequence for MCDU - Only autobrake MAX can be selected on the ground - Pushing autobrake MAX in the air, will disengage other enabled modes Display: - LS flag in FFD should be ILS for ILS landings Hardware: - Added support for Skalarki CB outputs - Updated Skalarki library FMS: - Fixed EFOB in FUEL PRED - Allow + or - in constraint altitude both in front of and at the end of the altitude - Refined conditions for engine out green dot speed - Apply engine out bank limit only below green dot speed - Fixed holding issues when holding was copied from SEC FPLN - Fixed holdings sometimes disappearing after modifying flightplan - Fix autoflight V/S speed reversion on ground - Fix NAV mode disengaging when entering holding as last leg in flight plan Misc: - Added gates for most electrical buses for external control of hardware - Do not unalign IRS if Prosim System is running while simulator is not yet loaded - Fix elevator trim speed when elevator is near limits - Added beta support for separate rudder/nosewheel control in P3D V4.5 or higher. To enable, Edit the aircraft.cfg file and add the line inhibit_rudder_on_steer = 1 under [contact_points] section. - Set FCU text lighting output to 0 when FCU is not powered September 30 Release version 1.40b13 ==================================== - Only autobrake MAX can be selected on the ground - Pushing autobrake MAX in the air, will disengage other enabled modes - Added Flood lt pedestal output left and Flood lt pedestal output right outputs to control individual lamps inside the pedestal flood light - Added Flood lt main center panel output left and Flood lt main center panel output right to control indivual MIP center flood lights - Apply engine out bank limit only below green dot speed - Fix elevator trim speed when elevator is near limits - Updated Skalarki library September 24 Release version 1.40b12 ==================================== - Set FCU text lighting output to 0 when FCU is not powered - Refined LGCIU signal 10 for gear release solenoid - Do not unalign IRS if Prosim System is running while simulator is not yet loaded - Added support for Skalarki CB outputs September 23 Release version 1.40b11 ==================================== - Updated Skalarki library and added support for Skalarki CB input September 22 Release version 1.40b10 ==================================== - Fix for ground roll parameter test September 22 Release version 1.40b9 =================================== - Added ground roll parameter test =================================== September 22 Release version 1.40b8 =================================== - Fixed holdings sometimes disappearing after modifying flightplan - Refined conditions for engine out green dot speed September 19 Release version 1.40b7 =================================== - Added CB's for audio control panels September 16 Release version 1.40b6 =================================== - Fixed holding issues when holding was copied from SEC FPLN September 15 Release version 1.40b5 =================================== - Fixed switching off FAC 1+2 should inop A/THR - Fixed FAC resetable fault does not resolve when resetting FAC - Fixes for too low terrain warning during landing September 14 Release version 1.40b4 =================================== - Added gates for most electrical buses for external control of hardware - Only autoextinguish APU fire if fire occured while on the ground September 11 Release version 1.40b3 =================================== - Fix FMS data source did not switch when ATT/HDG switch is used - Updated ECAM ALL button logic - Fixed power spike in DC essential bus causes tripping of A/THR - Changed LGCIU 1 ground/air relay to allow taking power from DC SVC bus when DC ESS is lost September 3 Release version 1.40b2 ================================== - LS flag in FFD should be ILS for ILS landings - Allow + or - in constraint altitude both in front of and at the end of the altitude - Fixed EFOB in FUEL PRED - Added rate limiter to nose wheel rotation speed - Added beta support for separate rudder/nosewheel control in P3D V4.5 or higher - Fix autoflight V/S speed reversion on ground - Fix NAV mode disengaging when entering holding as last leg in flight plan September 3 Release version 1.40b1 ================================== - Added boot sequence for MCDU August 31 Release version 1.39 ============================== Systems: - Added support for MCDU FM light Flight: - Improved normal law pitch stability (should improve stability issues during turbulence) Hardware: - Added light test display output to Skalarki RMP, trim and XPDR - Added support for FS Cockpit ASP pro and gear gravity extend hardware Fms: - Added A/C POSITION INVALID message and F/D flag during quick alignment - Fixed limit of EO ALT to max certified alt - LNAV fixes Misc: - Database fixes August 29 Release version 1.39b8 ================================ - updater infrastructure changes August 27 Release version 1.39b7 ================================ - Added support for MCDU FM light - Added light test display output to Skalarki RMP, trim and XPDR August 25 Release version 1.39b6 ================================ - Improved normal law pitch stability (should improve stability issues during turbulence) - Added A/C POSITION INVALID message and F/D flag during quick alignment August 19 Release version 1.39b5 ================================ - Fixed limit of EO ALT to max certified alt August 12 Release version 1.39b4 ================================ - Added support for FS Cockpit ASP pro and gear gravity extend hardware August 12 Release version 1.39b3 ================================ - Database fixes August 10 Release version 1.39b2 ================================ - Fix for timing issues during start up August 4 Release version 1.39b1 =============================== - LNAV fixes July 31 Release version 1.38 ============================ FMS: - Fixed CTE reversal in right turns - Improve vnav during holdings Systems: - Tuned pack parameters to prevent overheat in warmer weather - Improved engine start and cranking process Displays: - Lower ECAM will now always switch to ENG page when mode selector is set to IGN/START on the ground - Added PFD CHECK ALT flag - Improved VNAV decel indications in ND Misc: - Fix SDK access for older SDK versions - Fix configuration setting of FS time to use FS UTC time - Updated ECAM baro ref check - Updated terrain data download URL - Fixed crash in FMS when no complete flightplan was filled in July 30 Release version 1.38b9 ============================== - Fixed CTE reversal in right turns - Improve vnav during holdings - Fix SDK access for older SDK versions July 27 Release version 1.38b8 ============================== - Tuned pack parameters to prevent overheat in warmer weather July 27 Release version 1.38b7 ============================== - Fix configuration setting of FS time to use FS UTC time - Lower ECAM will now always switch to ENG page when mode selector is set to IGN/START on the ground July 20 Release version 1.38b6 ============================== - Updated ECAM baro ref check - Added PFD CHECK ALT flag July 16 Release version 1.38b5 ============================== - Updated terrain data download URL - Fix config save issue July 16 Release version 1.38b4 ============================== - Fixed crash in FMS when no complete flightplan was filled in July 14 Release version 1.38b3 ============================== - Fixed crash in FMS when no complete flightplan was filled in July 13 Release version 1.38b2 ============================== - Improved engine start and cranking process - Improved VNAV decel indications in ND July 8 Release version 1.38b1 ============================= - Fix for certification issue July 8 Release version 1.37 =========================== Systems: - Fixed indicators no longer working with DC ESS bus failure - Tuned system failure ECAM for DC ESS bus failure - Fixed Engine 1 loop A/B power source interchanged FMS: - Added DEST EFOB BELOW MIN logic - Fixed NAVRAD ILS slope not shown until ILS signal received Misc: - FWC emulator upgrade for better performance July 7 Release version 1.37b6 ============================= - Debug FWC issues July 4 Release version 1.37b5 ============================= - Fixed indicators no longer working with DC ESS bus failure - Tuned system failure ECAM for DC ESS bus failure - Fixed Engine 1 loop A/B power source interchanged - Added DEST EFOB BELOW MIN logic June 23 Release version 1.37b4 ============================== - Internal changes for testing - Fixed config not saving in prosim-system June 22 Release version 1.37b3 ============================== - Fixed config not saving in prosim-system June 22 Release version 1.37b2 ============================== - Fixed issues with ProsimDisplay June 9 Release version 1.37b1 ============================= - Fixed NAVRAD ILS slope not shown until ILS signal received - FWC emulator upgrade for better performance June 8 Release version 1.36 =========================== FMS: - Fixed step descend to same altitude as initial cruise altitude gets deleted - Fixed alternate time in INIT B not calculating - Improvements in single engine SRS mode - Improvements on engine out MCDU/FMS logic Systems: - Fixes to hot air valve - Fixed IDG low oil pressure ECAM warning when engine fails - Fixed hot air valve disagree ECAM on cold startup - Disconnect IDG when temperature over 200 Displays: - Added MCDU to ProsimDisplay - Smooth Vls based on actual flap position instead of detent - Don't show A/C symbol during lighttest MCDU: - Added failure view and removal to MCDU MAINT menu - Added door control to MCDU MAINT menu - Added missing APPROACH label to PROG page in approach phase Hardware: - Added support for nws disconnect button to FSC driver and fixed F/O locking solenoid in FSC sidestick Misc: - Fix for IVAO/Squawkbox FSUIPC xpdr information not getting through June 5 Release version 1.36b9 ============================= - Fix crash in ETP if cruisespeed null - Added support for nws disconnect button to FSC driver and fixed F/O locking solenoid in FSC sidestick - Added MCDU to ProsimDisplay June 2 Release version 1.36b8 ============================= - Smooth Vls based on actual flap position instead of detent - Don't show A/C symbol during lighttest June 1 Release version 1.36b7 ============================= - Fixes to hot air valve May 29 Release version 1.36b6 ============================= - Fixed step descend to same altitude as initial cruise altitude gets deleted May 27 Release version 1.36b5 ============================= - Fixed alternate time in INIT B not calculating - Fixed IDG low oil pressure ECAM warning when engine fails - Fixed hot air valve disagree ECAM on cold startup May 26 Release version 1.36b4 ============================= - Disconnect IDG when temperature over 200 - Improvements in single engine SRS mode May 22 Release version 1.36b3 ============================= - Improvements on engine out MCDU/FMS logic May 13 Release version 1.36b2 ============================= - Added failure view and removal to MCDU MAINT menu - Added door control to MCDU MAINT menu May 12 Release version 1.36b1 ============================= - Fix for IVAO/Squawkbox FSUIPC xpdr information not getting through May 12 Release version 1.35 =========================== FMS: - Reworked FMS time code. Waypoint timestamps are now continously reevaluated and wind data is mixed in more frequently - Added RTA functionality - Fix for broken pathing in some single bypass cases - Updated honeywell dir-to mcdu page logic - Added conditions for transitioning from climb directly to descend mode - Fixed step climb changing into step descend after performing climb MCDU: - Added dest EFOB to CRZ PERF page - Fixed incorrect FMS FOB value after startup with engines running Displays: - Large number of failures have been tuned to provide correct ECAM SD information Systems: - Large number of failures have been tuned in systems modeling - New pneumatic system with fan air control and better bleed air precooler outlet temperature - Improved ground horn control Misc: - Completed support for Prepar3d v5 - Support for ProSimA322 Visual Model 2020 2.0. - Support UNC path for database build. - Fixed database build for some add-on sceneries. - Fixed some ILS had missing DME data - Auto-install downloaded add-ins if possible - Added blue override pump state to IOS check items May 8 Release version 1.35b14 ============================= - Support for ProSimA322 Visual Model 2020 2.0. - Support UNC path for database build. May 6 Release version 1.35b13 ============================= - Added debug code for FMS capability status May 4 Release version 1.35b12 ============================= - Fix for broken paths in some single bypass cases May 1 Release version 1.35b11 ============================= - Fixed database build for some add-on sceneries. April 30 Release version 1.35b10 ================================ - Updates for visual model - Tuning of failures April 26 Release version 1.35b9 =============================== - Improved ground horn control - Many improvements to failure handling - Improvements in pneumatic system April 23 Release version 1.35b8 =============================== - Fixed some ILS had missing DME data April 21 Release version 1.35b7 =============================== - Added improved fan air valve simulation to improve bleed air temperature modeling - Extention of bleed air pressure and temperature modeling April 20 Release version 1.35b6 =============================== - Completed support for Prepar3d v5 - Many improvements to failure handling and ECAM April 15 Release version 1.35b5 =============================== - Lots of minor refinements to ECAM displays - Added support for connections to Prepar3D v5 (BGL scanner will be updated soon) April 7 Release version 1.35b4 ============================== - Updated honeywell dir-to mcdu page logic - Fixed issue with nullable value in RTA - Added blue override pump state to IOS check items March 30 Release version 1.35b3 =============================== - Fixed step climb changing into step descend after performing climb - Added conditions for transitioning from climb directly to descend mode March 30 Release version 1.35b2 =============================== - Prepare for the new flight model release, add support for new ProSim P3D Plug-In (to be released at a later date) - Auto-install downloaded add-ins if possible - Fixed incorrect FMS FOB value after startup with engines running March 28 Release version 1.35b1 =============================== - Reworked FMS time code. Waypoint timestamps are now continously reevaluated and wind data is mixed in more frequently - Added RTA functionality - Added dest EFOB to CRZ PERF page March 27 Release version 1.34 ============================= FMS: - Reworked init fuel planning page - Display current managed speed on MCDU PERF speed instead of default clb/des speed - Added SPD LIM EXCEEDED message and magenta/amber * next to FPLN SPD LIM - Calculate missed speed constraints in FPLN - Fixed changing FOB in MCDU should affect EFOB immediately - Fuel Pred EXTRA/TIME now uses dest EFOB instead of ALTN EFOB - Fixed PERF APPR speeds to show data for landing altitude Display: - Do not show ellipse around wpt in ND that have only a speed constraint - Adjusted ProsimCDU "green" color to be the same as ProsimDisplay "green" Hardware: - Fixed Cockpitsonic anti ice switches not working - Fix for CDU's not coming online at startup March 19 Release version 1.34b8 =============================== - Reworked init fuel planning page - Do not show ellipse around wpt in ND that have only a speed constraint March 18 Release version 1.34b7 =============================== - Display current managed speed on MCDU PERF speed instead of default clb/des speed - Added SPD LIM EXCEEDED message and magenta/amber * next to FPLN SPD LIM - Calculate missed speed constraints in FPLN March 12 Release version 1.34b6 =============================== - Adjusted ProsimCDU "green" color to be the same as ProsimDisplay "green" March 10 Release version 1.34b5 =============================== - Fixed Cockpitsonic anti ice switches not working - Fixed changing FOB in MCDU should affect EFOB immediately March 9 Release version 1.34b4 ============================== - Fuel Pred EXTRA/TIME now uses dest EFOB instead of ALTN EFOB March 5 Release version 1.34b3 ============================== - Fixed PERF APPR speeds to show data for landing altitude - Fixed graphical anomalies in display March 4 Release version 1.34b2 ============================== - More fixes for CDU's not coming online at startup March 3 Release version 1.34b1 ============================== - Fix for CDU's not coming online at startup February 27 Release version 1.33 ================================ Systems: - This releases uses the new World Magnetic Model that overrides all magnetic variation data from prepar3d with precise and current magnetic variation data. - Change power requirements of DU and DMC to continue functioning when DC power fails - Upgraded SEC code and moved flightcontrolsurfaces spoiler positions from axis domain to degree domain Flight: - Improved pitch stability in normal law Flight guidance: - Only capture G/S when within one dot FMS: - Prevent go around mode if TOGA is used after takeoff - NEW CRZ ALT message no longer showing when triggered from FCU - Enable alternate now shows NEW CRZ ALT and USING COST INDEX 0 messages on commit - Tuning of autoengagement of managed speed on ground based on FMS criterea MCDU: - Fixed commit temp not working on alternate flight plan Displays: - Tuning of layout of upper ECAM messages - Change terrain ND display to show only part in front of aircraft - Improved lag in PFD - Show ILS dagger on ND also in preflight and climb modes Hardware: - Added FSC sidestick driver February 24 Release version 1.33b11 =================================== - Prevent go around move if TOGA is used after takeoff February 21 Release version 1.33b10 =================================== - Fixed commit temp not working on alternate flight plan - NEW CRZ ALT message no longer showing when triggered from FCU - Enable alternate now shows NEW CRZ ALT and USING COST INDEX 0 messages on commit February 20 Release version 1.33b9 ================================== - Added MCDU power logging February 20 Release version 1.33b8 ================================== - Only capture G/S when within one dot - Tuning of upper ECAM messages February 15 Release version 1.33b7 ================================== - Tuning of autoengagement of managedspeed on ground based on FMS criterea February 13 Release version 1.33b6 ================================== - Change power requirements of DU and DMC to continue functioning when DC power fails - Change terrain ND display to show only part in front of aircraft February 7 Release version 1.33b5 ================================= - Fix roll pitch stability that was broken since b1 February 6 Release version 1.33b4 ================================= - Small improvement to world magnetic model - Added FSC sidestick driver February 4 Release version 1.33b3 ================================= - Added new World Magnetic Model that overrides all magnetic variation data from prepar3d with precise and current magnetic variation data - Improved lag in PFD - Improved pitch stability in normal law Januari 29 Release version 1.33b1 ================================= - Show ILS dagger on ND also in preflight and climb modes - Upgraded SEC code and moved flightcontrolsurfaces spoiler positions from axis domain to degree domain January 24 Release version 1.32 =============================== FMS: - Added limits to gust calculation in ground speed mini function - Removed extra 10 kts buffer from descend speed target below default speed restriction altitude - Fixed RADNAV page should used shown ILS frontcourse or show amber dashes - Do not list missed approach legs in DIR TO page Displays: - Improvements to speed tape speed trend pointer - Added VOR and ADF bearing noise - Correct reversal of altitude for block constraints in ND CSTR mode Flight: - Tuning of speedbrakes during CMD flight - Tuned pitch responsiveness during high alpha flight Systems: - Added signal acquisition time to radios - Improved FWC state calculations to allow ECAM TO Config button to switch to phase 2 - Fix crash in virtual VOR signal code January 23 Release version 1.32b8 ================================= - Added limits to gust calculation in ground speed mini function - Improvements to speed tape speed trend pointer January 22 Release version 1.32b7 ================================= - Tuning of speedbrakes during CMD flight - Removed extra 10 kts buffer from descend speed target below default speed restriction altitude January 22 Release version 1.32b6 ================================= - Added VOR and ADF bearing noise January 17 Release version 1.32b5 ================================= - Fixed ILS2 not working because of signal acquisition January 16 Release version 1.32b4 ================================= - Fixed RADNAV page should used shown ILS frontcourse or show amber dashes - Added signal acquisition time to radios - Improved FWC state calculations to allow ECAM TO Config button to switch to phase 2 January 13 Release version 1.32b3 ================================= - Correct reversal of altitude for block constraints in ND CSTR mode - Do not list missed approach legs in DIR TO page - Fix crash in virtual VOR signal code January 11 Release version 1.32b2 ================================= - Tuned pitch responsiveness during high alpha flight January 7 Release version 1.32b1 ================================ - Added extra SDK datarefs December 31 Release version 1.31 ================================ Systems: - Reworked IAE EGT data - Fixed ECAM signs status not responding to status of seat belt signs - Updated XPDR panel user interface - Added low air pressure start modeling - Fixes for GPWS too low terrain warning FMS: - Fixed holdings not updating in TMPY FLPN when parameters are changed - Prevent triple click in some cases during departure - ND now jumps PLAN center position to destination airport when STAR or Approach is selected - Added CLK IS TAKE OFF TIME message and RWY/LS MISMATCH message - Added support for localiser back beam navigation - LNAV fixes Displays: - Fixes to rudder trim ECAM display - Tuned appareance of LOG/GS displays Misc: - Tuning to virtual navaids - Fixes for DME signals of ILS stations - Turn weather radar image full red on max gain - Upgraded web libraries - Added more IOS Check items for common configuration errors Hardware: - Changed FDS ACP panel to new mapping December 27 Release version 1.31b11 =================================== - Fixed holdings not updating in TMPY FLPN when parameters are changed December 23 Release version 1.31b9 ================================== - Prevent triple click in some cases during departure - Reworked IAE EGT data - Fixed to rudder trim ECAM display - Fixed ECAM signs status not responding to status of seat belt signs - Tuned appareance of LOG/GS displays - Updated XPDR panel user interface - ND now jumps PLAN center position to destination airport when STAR or Approach is selected - Added CLK IS TAKE OFF TIME message and RWY/LS MISMATCH message December 16 Release version 1.31b6 ================================== - Added support for localiser back beam navigation - Tuning to virtual navaids - Added SDK stall variable December 9 Release version 1.31b5 ================================= - Turn weather radar image full red on max gain - Added low air pressure start modeling December 6 Release version 1.31b4 ================================= - Fixes for GPWS too low terrain warning December 4 Release version 1.31b3 ================================= - Changed FDS ACP panel to new mapping December 3 Release version 1.31b2 ================================= - Fixes for GPWS too low terrain warnings during landing - Fixes for DME signals of ILS stations - Upgraded web libraries November 27 Release version 1.31b1 ================================== - Use AIRAC database for ILS data like freq and ID - Fix for spurious too low terrain warnings - LNAV fixes November 22 Release version 1.30 ================================ Displays: - Updates to Bleed and APU ECAM pages - Increased visible WPT distance in ND to 80NM Systems: - Added A/T inhibit by pushbutton function - Added FCU brightness control to ProSimDisplay - Fix trim wheel runaway after setting trim via SDK - APU bleed ON indication should always be on when switched is pushed - Reversers should not be available if EDP is offline Hardware: - Fixes for FSCockpit brightness panel - Added support for FSCockpit backlight module - Poldragonet WXR panel tilt is now calibratable. Please configure the tilt axis in the configuration screen. SDK: - Fix SimConnect state reporting ready too early - Fix SDK "ready" value when using SimConnect - Do not allow writing to FPLN FROM field Misc: - Improve reliability of SimConnect reposition logic November 18 Release version 1.30b11 =================================== - Added A/T inhibit by pushbutton function November 13 Release version 1.30b10 =================================== - Added FCU brightness control to ProSimDisplay - Fixes for FSCockpit brightness panel November 13 Release version 1.30b9 ================================= - Fix altitude freeze instantly unfreezing November 13 Release version 1.30b8 ================================= - Fix trim wheel runaway after setting trim via SDK November 12 Release version 1.30b7 ================================= - Fix SimConnect state reporting ready too early November 12 Release version 1.30b6 ================================= - Improve reliability of SimConnect reposition logic November 12 Release version 1.30b5 ================================= - Add more logging to troubleshoot SimConnect ready state November 11 Release version 1.30b4 ================================= - Updates to Bleed and APU ECAM pages - Added support for FSCockpit backlight module November 11 Release version 1.30b3 ================================= - Fix SDK "ready" value when using SimConnect November 8 Release version 1.30b2 ================================= - APU bleed ON indication should always be on when switched is pushed - Poldragonet WXR panel tilt is now calibratable. Please configure the tilt axis in the configuration screen. - Increased visible WPT distance in ND to 80NM October 29 Release version 1.30b1 ================================= - Reversers should not be available if EDP is offline - Do not allow writing to FPLN FROM field October 25 Release version 1.29 =============================== Systems: - N/W steering now on yellow hydraulic by default. Can still be switched back to green in IO Cockpit Setup. - Added option for 844 voice channel spacing - Improvements in engine out managed speed selection and handling of LVR MCT message - Check status of FAC instead of computer status to determine active law - Fixed overspeed warning should occur at VMO + 4 FMS: - Refined autosequencing to prevent erasing tracks that are in opposite direction Displays: - Vls should always be fixed and disappear when below VAlphaprot - Max resolution of GW in ECAM changed to 100 for KG or 200 for LBS - Fixed MACH SEL FMA message formatting Flight: - Improvement in autopilot rudder control for assymetric thrust - Improved normal law high speed protection Hardware: - Added calibrator to weather radar tilt input for precise calibration - Fix crash in Skalarki driver Misc: - Added extra rudder trim decimal output - When parsing waypoint as airport/rwy combination, no longer use starting positions, but instead take lat/lon of center and translate to half of the length of the runway to calculate threshold position - Fixed strobe light should be off when on the ground if switch is in AUTO stat October 23 Release version 1.29b10 ================================== - N/W steering now on yellow hydraulic by default. Can still be switched back to green in IO Cockpit Setup. - Added calibrator to weather radar tilt input for precise calibration October 19 Release version 1.29b9 ================================= - Vls should always be fixed and disappear when below VAlphaprot October 17 Release version 1.29b8 ================================= - Fix for A/P yawing at low speed October 17 Release version 1.29b7 ================================= - Fix crash in Skalarki driver October 17 Release version 1.29b5 ================================= - Tuned high gain rudder coordination - Added extra rudder trim decimal output October 11 Release version 1.29b4 ================================= - Added option for 844 voice channel spacing - When parsing waypoint as airport/rwy combination, no longer use starting positions, but instead take lat/lon of center and translate to half of the length of the runway to calculate threshold position - Max resolution of GW in ECAM changed to 100 for KG or 200 for LBS - Improvement in autopilot rudder control for assymetric thrust October 07 Release version 1.29b3 ================================= - Refined autosequencing to prevent erasing tracks that are in opposite direction - Improvements in engine out managed speed selection and handling of LVR MCT message October 04 Release version 1.29b2 ================================= - Fixed strobe light should be off when on the ground if switch is in AUTO state - Check status of FAC instead of computer status to determine active law October 02 Release version 1.29b1 ================================= - Improved normal law high speed protection - Fixed MACH SEL FMA message formatting - Fixed overspeed warning should occur at VMO + 4 September 30 2019 Release version 1.28 ====================================== !! The database format for navigation data has changed. Airac cycle 1901 is included in this release in the new format. !! Please make sure you download the correct new format from your navigation data supplier. If you don't have a correct !! database installed, ProSim will fall back to the included 1901 airac cycle. FMS: - LNAV fixes - FMGC should use FAC grossweight in the air System: - Fixed nose wheel taxi and takeoff positions inverted - Added pitot blockage failures - Added custom vibration model - Clear manually selected ECAM page when pressing CLR to allow ECAM procedure to complete correctly if manual or advisory pages are selected - FAC should use exact calculated grossweight instead of FMS GW - Improved pitch stability in normal law during acceleration - Improved alpha protection law - Reworked effect of speedbrake on Vls - Fixed alpha protection mode should command alpha prot if sidestick is neutral - Added DME C/B's and nav override indication on ND Hardware: - Updated skalarki SDK to 5.1 profiler version - Removed Cockpit Concept DCDU driver (please use Cockpit Connect software 1.0.9.6 or newer instead). - Added support for Skalarki loadspeaker and WXR brightness controls - Fix for Skalarki ADIRS display - Added individual selection of encoder types for EFIS and FCU panels for FSCockpit hardware Displays: - Improved indications of safety valve and fully open outflow valve in flight in ECAM press page - Improved reverser modeling and ECAM pages Misc: - Added 64 bit support to ProSim System module - Added FAC characteristic speeds to SDK September 30 2019 Release version 1.28b8 ======================================== - LNAV fixes September 23 2019 Release version 1.28b7 ======================================== - Fixed nose wheel taxi and takeoff positions inverted - LNAV fixes September 23 2019 Release version 1.28b6 ======================================== - Added pitot blockage failures - Added custom vibration model - Clear manually selected ECAM page when pressing CLR to allow ECAM procedure to complete correctly if manual or advisory pages are selected September 19 2019 Release version 1.28b5 ======================================== - Fixed Vls always 5 kts too high - Updated skalarki SDK to 5.1 profiler version - FMGC should use FAC grossweight in the air September 17 2019 Release version 1.28b4 ======================================== !! The database format for navigation data has changed. At the moment, Navigraph and Aerosoft have confirmed they are going to !! deliver both the old and the new format very soon, but the new format is not yet available. Airac cycle 1901 is included in !! this release in the new format. If you require an up to date airac cycle, please don't upgrade to ProSimA322 1.28b4 or higher !! until Navigraph and Aerosoft offer the new format. - Added 64 bit support to ProSim System module - Removed Cockpit Concept DCDU driver (please use Cockpit Connect software 1.0.9.6 or newer instead). - Added support for Skalarki loadspeaker and WXR brightness controls - Fix for Skalarki ADIRS display - LNAV fixes - Improved indications of safety valve and fully open outflow valve in flight in ECAM press page September 10 2019 Release version 1.28b3 ======================================== - Improved reverser modeling and ECAM pages - FAC should use exact calculated grossweight instead of FMS GW - Improved pitch stability in normal law during acceleration - Improved alpha protection law September 7 2019 Release version 1.28b2 ======================================= - Reworked effect of speedbrake on Vls - Fixed alpha protection mode should command alpha prot if sidestick is neutral September 5 2019 Release version 1.28b1 ======================================= - Added individual selection of encoder types for EFIS and FCU panels for FSCockpit hardware - Added FAC characteristic speeds to SDK - Updated skalarki SDK - Added DME C/B's and nav override indication on ND August 30 2019 Release version 1.27 =================================== FMS: - Fix for spurious triple click alerts - Reworked MCDU winds pages - Do not show VNAV data for missed approach legs - Do not calculate ETP when source and destination are identical - LNAV fixes - VNAV fixes - Along track waypoint now allow arbitrary distances Systems: - Added engine ignition C/B's and no ignition failure - Updated logic for showing ecam engine page on the ground with mode selector in start position - Revised popup of ECAM ENG page during engine start and engine failure - Fixed EIU fault during engine shutdown in flight - Fixed max PSI of alternate brake during G+Y hyd failure - Fixed autobrake targets not matched - Added lighting C/B's - Fixed IAE engine idle EPR values Display: - Fixed display of CSTR in ND for block altitude constraints Hardware: - Added gear retract release gate for solenoids that release the gear lever - Fixed engine not shutting down if prosim started with switches in off state - Added aditional backlighting gates for seperate control of overhead/glareshield and pedestal Misc: - Allow tuning of TACANs - Fixed ProSim Display configuration screen label August 27 2019 Release version 1.27b8 ===================================== - Added gear retract release gate for solenoids that release the gear lever - Fix for spurious triple click alerts - Added engine ignition C/B's and no ignition failure August 22 2019 Release version 1.27b7 ===================================== - Allow tuning of TACANs - Reworked MCDU winds pages August 20 2019 Release version 1.27b6 ===================================== - Do not show VNAV data for missed approach legs - Update to logic for showing ecam engine page on the ground with mode selector in start position August 18 2019 Release version 1.27b5 ===================================== - Fixed EIU fault during engine shutdown in flight - Do not calculate ETP when source and destination are identical August 14 2019 Release version 1.27b4 ===================================== - VNAV fixes August 12 2019 Release version 1.27b3 ===================================== - Fixed max PSI of alternate brake during G+Y hyd failure - Fixed display of CSTR in ND for block altitude constraints - Fixed engine not shutting down if prosim started with switches in off state August 9 2019 Release version 1.27b2 ==================================== - Revised popup of ECAM ENG page during engine start and engine failure - Along track waypoint now allow arbitrary distances - Lnav fixes - Added aditional backlighting gates for seperate control of overhead/glareshield and pedestal - Fixed autobrake targets not matched August 5 2019 Release version 1.27b1 ==================================== - Added lighting C/B's - Fixed IAE engine idle EPR values - Fixed ProSim Display configuration screen label August 2 2019 Release version 1.26 ================================== This releases mostly adds a lot of circuit breakers and also has these fixes: FMS: - Lnav improvements - Fixes crash in lateral offset Systems: - Made ice detection system optional - Fixed auto ext ground test fires squib - Adjusted brakes to allow a max of 1000 PSI if anti skid is inop - Added ABCU and alternate brake fault Flight guidance: - Tuned ALT* final capture guidance Misc: - Added simulator rate control to MCDU main menu Hardware: - Added missing Skalarki ECAM ALL button July 26 2019 Release version 1.26b6 =================================== - Lnav fixes - Fixes crash in lateral offset July 23 2019 Release version 1.26b5 =================================== - Lnav improvements - Made ice detection system optional July 23 2019 Release version 1.26b4 =================================== - Added simulator rate control to MCDU main menu - Added more C/B's July 16 2019 Release version 1.26b3 =================================== - Added missing Skalarki ECAM ALL button - Fixed auto ext ground test fires squib - Added more C/B's July 12 2019 Release version 1.26b2 =================================== - Tuned ALT* final capture guidance - Added more C/B's July 8 2019 Release version 1.26b1 ================================== - Adjusted brakes to allow a max of 1000 PSI if anti skid is inop - Added THS actuator motor circuit breakers - Added ABCU and alternate brake fault July 5 2019 Release version 1.25 ================================ FMS: - Fixes for lateral offset - Fixed FMS switching to preflight after landing, causing autotuned ILS signal to disappear - LNAV rendering improvements for some departures - Fixed vnav distance inaccuracies - Fixed ECAM CRZ page jumps back to ENG page at flap extension - Fixes for holdings at FROM point - Changes in F/D architecture to improve adjustability Flight guidance: - Rework of ALT* capture mode Systems: - Fixed FAC stall speed calculation did not correctly handle slats locked up - Cancel CRC sound if CLR pressed - Reworked break system for more realism - Added surface wind dependent break cooling - Fixes in ECAM screen/procedures for brakes and gear faults - Added MCDU recoverable failures - Improvements to PTU control Hardware: - Fixed FSCockpit ASP Int light not working Misc: - Fixed surface winds not working in IOS July 4 2019 Release version 1.25b10 =================================== - Fixed crashes in lateral offsets July 2 2019 Release version 1.25b9 ================================== - Further tuning of ALT* capturing - Fixes for lateral offset - Fixed FMS switching to preflight after landing, causing autotuned ILS signal to disappear June 30 2019 Release version 1.25b8 =================================== - Fixed FAC stall speed calculation did not correctly handle slats locked up - Cancel CRC sound if CLR pressed - LNAV rendering improvements for some departures June 29 2019 Release version 1.25b7 =================================== - Fixed FSCockpit ASP Int light not working - Fixed vnav distance inaccuracies June 27 2019 Release version 1.25b6 =================================== - Fixed ECAM CRZ page jumps back to ENG page at flap extension June 26 2019 Release version 1.25b5 =================================== - Rework of ALT* capture mode June 25 2019 Release version 1.25b4 =================================== - Fixed surface winds not working in IOS - Reworked break system for more realism - Added surface wind dependent break cooling June 21 2019 Release version 1.25b3 =================================== - Fixes in ECAM screen/procedures for brakes and gear faults - Added MCDU recoverable failures June 17 2019 Release version 1.25b2 =================================== - Fixes for holdings at FROM point - Improvements to PTU control June 11 2019 Release version 1.25b1 =================================== - Changes in F/D architecture to improve adjustability June 7 2019 Release version 1.24 ================================ FMS: - Added support for LNAV track offset - LNAV improvements for altitude realted waypoints - Fixed SEC FLPN activation should insert PPOS and DISCO if not in sequence - Fixed fly-over condition disappearing after flight plan modification Flight guidance: - Tuned ALT* capturing to reduce overshoot Displays: - Fixed ECAM HYD page Rat indication when RAT deployed Hardware: - Fixed interchanged LSKR5 and 6 buttons on OpenCockpits MCDU - Added support for FSCockpit C/B panel Systems: - Fixed a/skip inop not showing during BSCU fault Misc: - Fix config issue where Lever motor output could not be configured to devices using text inputbox as selection June 6 2019 Release version 1.24b8 ================================== - LNAV updates June 6 2019 Release version 1.24b7 ================================== - Fixed crash - LNAV updates June 3 2019 Release version 1.24b6 ================================== - Tuned ALT* capturing to reduce overshoot - LNAV fixes June 1 2019 Release version 1.24b5 ================================== - LNAV fixes for altitude based waypoints May 30 2019 Release version 1.24b4 ================================== - Fixed ECAM HYD page Rat indication when RAT deployed - Fixed interchanged LSKR5 and 6 buttons on OpenCockpits MCDU May 28 2019 Release version 1.24b3 ================================== - LNAV fixes - Fixed a/skip inop not showing during BSCU fault May 21 2019 Release version 1.24b2 ================================== - Fixed SEC FLPN activation should insert PPOS and DISCO if not in sequence - Fix config issue where Lever motor output could not be configured to devices using text inputbox as selection May 20 2019 Release version 1.24b1 ================================== - Add initial support for the new FM - Added initial support for LNAV offset - Added support for FSCockpit C/B panel - Fixed fly-over condition disappearing after flight plan modification May 11 2019 Release version 1.23 ================================ Systems: - Improved GPWS don't sink message FMS: - Added support for equi-time point - Added support for polar nav (true referencing) with or without NORTH REF button on MIP - Large rewrite of LNAV/VNAV core. This allows future updates to LNAV rendering. Currently, the new LNAV core has new support for single waypoint bypass. - A/THR should announce THR IDLE during autoland flare - Allow dir to with radial in/out to have magnetic or true referenced input - Fixed magnetic variation error in dir to radial out - Show V/S dashed on ground also if CLB armed - Fixed extra/time does not take min dest fob in account Hardware drivers: - FSUIPC driver performance improvements - Fixed issue with Poldragent engine 2 fire agent indicator - Added option for 2x encoder support in FSCockpit hardware Misc: - Added gate output for gear handle inhibit - Fixed incorrect p3d flap command during flap/slat fault - SDK DataRef "aircraft.fmgc.flightPhase" has been renamed to "aircraft.fmc.flightPhase". - SDK DataRefs "system.config.*" now include the cockpit setup group name. - Seveval SDK DataRefs have been added. - Added filter to brake pressure indicators May 8 2019 Release version 1.23b11 ================================== - Equi-time point improvements - Added gate output for gear handle inhibit May 8 2019 Release version 1.23b10 ================================== - Added support for equi-time point May 7 2019 Release version 1.23b9 ================================= - A/THR should announce THR IDLE during autoland flare - Fix true ref for closest airports CDU page - Fixed issue with Poldragent engine 2 fire agent indicator May 2 2019 Release version 1.23b8 ================================= - Fixed magnetic variation error in dir to radial out - Allow dir to with radial in/out to have magnetic or true referenced input April 30 2019 Release version 1.23b7 ==================================== - Added support for polar nav - Fixed incorrect p3d flap command during flap/slat fault April 25 2019 Release version 1.23b6 ==================================== - Fixed engine start issues April 19 2019 Release version 1.23b5 ==================================== - SDK DataRef "aircraft.fmgc.flightPhase" has been renamed to "aircraft.fmc.flightPhase". - SDK DataRefs "system.config.*" now include the cockpit setup group name. - Seveval SDK DataRefs have been added. - FSUIPC driver performance improvements - Added support for FSCockpit C/B board - Improved GPWS don't sink message - Added option for 2x encoder support in FSCockpit hardware - Show V/S dashed on ground also if CLB armed April 15 2019 Release version 1.23b4 ==================================== - LNAV fixes April 14 2019 Release version 1.23b3 ==================================== - Added filter to brake pressure indicators April 11 2019 Release version 1.23b2 ==================================== - Fix for VNAV jumps - Fixed extra/time does not take min dest fob in account April 11 2019 Release version 1.23b1 ==================================== - Large rewrite of LNAV/VNAV core. This allows future updates to LNAV rendering. Currently, the new LNAV core has new support for single waypoint bypass. April 11 2019 Release version 1.22 ================================== FMS: - LNAV/VNAV fixes - Fixes for LNAV/VNAV and manual legs Display: - Fixed some speedtape feature visible when SPEED flag is shown - Fix display freezes Systems: - Allow characteristic speed computation even when FAC switches are off - Added nose wheel steering fault - Fixed A/P not disconnecting when in direct law - Disabled TCAS when IR1 fails - Added failures for elec hydraulic pumps - Added failures for heating of air data elements - ECAM fixes Hardware: - Reduce intercom latency when both capture and playback devices are using the same ProSimA322-Audio instance - Added support for Skalarki gravity gear extend - Increased Skalarki elevator trim reset speed Flight guidance: - LNAV and LOC capture improvements Misc: - Added MCDU clear_line virtual key - Fixed MCDU XML data lower case "kts" April 5 2019 Release version 1.22b8 =================================== - Reduce intercom latency when both capture and playback devices are using the same ProSimA322-Audio instance - Added support for Skalarki gravity gear extend - Allow characteristic speed computation even when FAC switches are off - Fixed some speedtape feature visible when SPEED flag is shown March 28 2019 Release version 1.22b7 ==================================== - Added nose wheel steering fault - Fixed A/P not disconnecting when in direct law - Disabled TCAS when IR1 fails March 26 2019 Release version 1.22b6 ==================================== - Added failures for elec hydraulic pumps - Added failures for heating of air data elements - ECAM fixes March 23 2019 Release version 1.22b5 ==================================== - LNAV and LOC capture improvements March 22 2019 Release version 1.22b4 ==================================== - Added MCDU clear_line virtual key - Fixed MCDU XML data lower case "kts" - LNAV fixes March 20 2019 Release version 1.22b3 ==================================== - LNAV/VNAV fixes March 19 2019 Release version 1.22b2 ==================================== - Fixed Skalarki elevator trim March 15 2019 Release version 1.22b1 ==================================== - Fix display freezes - Fixes for LNAV/VNAV and manual legs - Increased Skalarki elevator trim reset speed March 15 2019 Release version 1.21 ================================== FMS: - Improvements in takeoff trim setting making rotation with normal trim settings more realistic - Improvemed FBW roll response - Also auto tune ILS for LOC approaches - Fixed oscillating modes when engine fails during VNAV cruise flight - Do not select missed approach legs as targets for stringing star transition to approach Displays: - Make sure N1 gauge reaches minimum value when engine is off - Fixed pedestal XPDR display references incorrect data Systems: - GPWS TERR and CAT 2 INOP when dual FCU fails - Fixes for STS page during IR faults - A/THR failure split into A/THR 1 and 2 - Removed IRS total failure and added "IR failure", which only fails ATT + POS Hardware: - Fixed FSCockpit triple gauge has incorrect range for accu pressure Misc: - Added terrain ahead pullup sound - Make sure radios provide no signal if no request for any frequency is available - Reset FMS after landing now also applied to resetting after failure - Fixed incorrect data for engine values after engine start MCDU: - Fixed various issues with return to SEC FPLN March 13 2019 Release version 1.21b8 ==================================== - Fixed elevator trim not correct after landing causing nose down issues - Added terrain ahead pullup sound March 12 2019 Release version 1.21b7 ==================================== - Improvements in takeoff trim setting making rotation with normal trim settings more realistic - Improvemed FBW roll response March 11 2019 Release version 1.21b6 ==================================== - Fix crash on startup introduced in 1.21b5 March 10 2019 Release version 1.21b5 =================================== - GPWS TERR and CAT 2 INOP when dual FCU fails March 5 2019 Release version 1.21b4 =================================== - Fixed FSCockpit triple gauge has incorrect range for accu pressure - Fixes for STS page during IR faults March 3 2019 Release version 1.21b3 =================================== - Also auto tune ILS for LOC approaches - Make sure radios provide no signal if no request for any frequency is available - A/THR failure split into A/THR 1 and 2 - Removed IRS total failure and added "IR failure", which only fails ATT + POS - Make sure N1 gauge reaches minimum value when engine is off - Fixed oscillating modes when engine fails during VNAV cruise flight - Do not select missed approach legs as targets for stringing star transition to approach February 26 2019 Release version 1.21b2 ======================================= - Fixed pedestal XPDR display references incorrect data - Fixed various issues with return to SEC FPLN - Reset FMS after landing now also applied to resetting after failure - Fixed incorrect data for engine values after engine start February 26 2019 Release version 1.20 ===================================== NOTE: Requires .NET Version 4.7.2 or newer! FMS: - Fixed STAR cleared when modification to flightplan made - Fixes for processing of manual legs - LNAV improvements - Improvements in calculation of estimated position error - Improved hybrid GPIRS position calculation - Allow FMS to calculate more flightplan data without full flightplan - Fixed climb default speed limit not assigned correctly when set on departure airport - Fixed airspeed bug not showing target during EXPED climb/descend - Added flightplan restringing between SID -> STAR and SID -> approach - Fixed FMS route restring from enroute to approach - Activate alternate fpln if dir to to an alternate flightplan waypoint is performed during go around - Fixed selection of departure and approach transitions not working for ALTN/SEC flpns - Fixes for T/D markers on ND Systems: - Improvements in EGPWS - Added EGPWS audio - Added GPWS ECAM data - Fixes for terrain fault during dual FMGC fault - Fixed inverted online networking squawk logic - Fix freeze when radionav deselected - Improvements in engine start data - Fixes for manual start - Improvements in engine/apu response to fuel starvation Displays: - L/DEV scales for RNP sid now also shown during taxi - Add high DPI screen support to all modules - Display: Added WXR sweep smoothing option to Direct2D mode - Display: Fix bad Direct2D image quality when started without titlebar Flight Guidance: - Retuned autopilot pitch control - Fixed ALT* altitude overshoots - Keep speed bug on V2 during SRS single engine flight - Improvements in alternate law low/high speed stability protection Hardware: - Added support for MCDU brightness buttons for Poldragonet MCDU CDU: - Fix crash in MCDU navaids page - Plan mode can now center on pseudowaypoints Misc: - Fixed bgl scanner to extract airports without runways - Added ability to add axes configuration and nullzones to hardware that uses the SDK to interface through the new [SDK] driver - Added Cockpit Setup option for GND TEMP in INIT page - Fixes for minimums and 200 above callouts cutting off - Audio: switch from DirectSound to Core Audio (fixes issues with certain wav files) February 26 2019 Release version 1.20b19 ======================================== - Reduce CPU load - Added support for MCDU brightness buttons for Poldragonet MCDU February 21 2019 Release version 1.20b18 ======================================== - Improvements in EGPWS - Fixed ALT* altitude overshoots February 18 2019 Release version 1.20b17 ======================================== - Fixed crash in cockpit concepts driver February 14 2019 Release version 1.20b16 ======================================== - Keep speed bug on V2 during SRS single engine flight - Fixes for terrain fault during dual FMGC fault February 13 2019 Release version 1.20b15 ======================================== - Fixes for EGPWS February 13 2019 Release version 1.20b14 ======================================== - Fix for Skalarki driver crash February 12 2019 Release version 1.20b13 ======================================== - Fixed STAR cleared when modification to flightplan made - Fix crash in MCDU navaids page February 11 2019 Release version 1.20b12 ======================================== - Fixes for processing of manual legs - Added EGPWS audio - Added GPWS ECAM data February 6 2019 Release version 1.20b11 ======================================= - LNAV improvements - Plan mode can now center on pseudowaypoints - Improvements in calculation of estimated position error February 4 2019 Release version 1.20b10 ======================================= - Fixes for issues with previous builds February 3 2019 Release version 1.20b9 ====================================== - Allow FMS to calculate more flightplan data without full flightplan February 1 2019 Release version 1.20b8 ====================================== - Fixed inverted online networking squawk logic - Fixed bgl scanner to extract airports without runways - Added ability to add axes configuration and nullzones to hardware that uses the SDK to interface through the new [SDK] driver January 31 2019 Release version 1.20b7 ====================================== - Retuned autopilot pitch control - Improved hybrid GPIRS position calculation January 30 2019 Release version 1.20b6 ====================================== - Improvements in alternate law low/high speed stability protection - Fixed issue with downgrading to latest stable version January 29 2019 Release version 1.20b5 ====================================== - Fixed SimConnect crashes January 29 2019 Release version 1.20b4 ====================================== - Fixed climb default speed limit not assigned correctly when set on departure airport - Fixed airspeed bug not showing target during EXPED climb/descend - Added flightplan restringing between SID -> STAR and SID -> approach - Fix freeze when radionav deselected - Activate alternate fpln if dir to to an alternate flightplan waypoint is performed during go around January 27 2019 Release version 1.20b3 ====================================== - Fixed FMS route restring from enroute to approach - Fixed selection of departure and approach transitions not working for ALTN/SEC flpns - L/DEV scales for RNP sid now also shown during taxi - Added Cockpit Setup option for GND TEMP in INIT page - Fixes for T/D markers on ND January 25 2019 Release version 1.20b2 ====================================== - Add high DPI screen support to all modules - Fixes for manual start - Fixes for minimums and 200 above callouts cutting off January 21 2019 Release version 1.20b1 ====================================== - Display: Added WXR sweep smoothing option to Direct2D mode - Improvements in engine start data - Improvements in engine/apu response to fuel starvation - Audio: switch from DirectSound to Core Audio (fixes issues with certain wav files) - Display: Fix bad Direct2D image quality when started without titlebar January 18 2019 Release version 1.19 ==================================== FMS: - Fixed missing discontinuity after missed approach legs when initiating go-around - Revert to default FMA modes when APPR armed and APPR changed in MCDU - Refined condition for FMS transition to DES phase - LNAV fixes Systems: - Added fuel leak failures - Improvements for single and dual FMS failure - Added high idle for single bleed operation - Added engine high N1 failure - Added engine high EGT failure - Fixed IOS 2000 gpws signal inhibit also inhibits 500 gpws signal - Added dynamic bleed pressure based on N1 - Improved FADEC handling of master switches and fire button - Added MCDU C/B's Displays: - Fixed ND chrono display overlapping text in hour mode - Fixed WXR image jumps with ASN - Fix for ASN weather radar - Fixed PFD showing both LS and mach Flight Guidance: - Improved alt* mode Hardware: - Fixed FDS CDU FM1 light not working CDU: - Improved CDU message system - Added LAT DISCONT AHEAD Message - Added departure NO SID option Misc: - No longer updating internal navigation radio frequencies from simulator - Added checking of frequencies sent through SDK - Add support for secondary ASN radar file location (c:\ProgramData\ProSim\radar.bin) - Fixed ILS nav sounds not working - Improved ProSimAudio device selection UI January 17 2019 Release version 1.19b9 ====================================== - Added fuel leak failures January 15 2019 Release version 1.19b8 ====================================== - No longer updating internal radio frequencies from navigation rations from simulator - Added checking of frequencies sent through SDK - Fixed ND chrono display overlapping text in hour mode - Improvements for single and dual FMS failure January 14 2019 Release version 1.19b7 ====================================== - Added high idle for single bleed operation - Added engine high N1 failure - Add support for secondary ASN radar file location (c:\ProgramData\ProSim\radar.bin) - Fixed WXR image jumps with ASN January 11 2019 Release version 1.19b6 ====================================== - Fixed FDS CDU FM1 light not working - Fixed IOS 2000 gpws signal inhibit also inhibits 500 gpws signal - Fixed ILS nav sounds not working - Added dynamic bleed pressure based on N1 - Improved FADEC handling of master switches and fire button January 8 2019 Release version 1.19b5 ===================================== - Fixed missing discontinuity after missed approach legs when initiating go-around - Improved alt* mode January 4 2019 Release version 1.19b4 ===================================== - Fix for ASN weather radar - Improved CDU message system January 3 2019 Release version 1.19b3 ===================================== - Revert to default FMA modes when APPR armed and APPR changed in MCDU - Fixed PFD showing both LS and mach January 1 2019 Release version 1.19b2 ===================================== - Improved single and no FMGC operation - Refined condition for FMS transition to DES phase December 30 2018 Release version 1.19b1 ======================================= - Added LAT DISCONT AHEAD Message - Added departure NO SID option - LNAV fixes - Added MCDU C/B's - Improved ProSimAudio device selection UI December 28 2018 Release version 1.18 ===================================== FMS: - FMS will now update the calculated position of altitude pseudo waypoints to make sure they are sequenced correctly - Fixed inproper VNAV data when flightplan is very short and T/C overlaps T/D Systems: - Fixed VNAV crash - Fixed XPDR 1 power failure should allow usage of XPDR 2 - Adjusted fuel tank sizes - Added non cancellable ECAM items - Updated stall warning system - Updated ECAM for hung start - More protection against spurious speed callouts - Vnav fixes - Fixed issues with manually tuning VOR stations on RMP Displays: - L/DEV scale now available during RNAV sids - Fixed ND zoom factor during FCU 1+2 fault - Updated overhead graphics - Fixes for PFD overlapping data and V/DEV L/DEV scales - Added missing L/DEV label Flight Guidance: - Updated open climb logic for short altitude deltas - Prevent APPR button from activating an ILS approach if LOC signal is received on radio when ILS was not manually tuned - Updated upper limit of ECON speed range when speed restriction is active Hardware: - Fixed Poldragonet XPDR 1/2 switch reversal CDU: - Added possibility to enter waypoint on T/C and T/D markers - Allow LATREV from discontinuity - Added MCDU brightness keys Misc: - Improved BGL extraction to prevent airports without runways - Fixed incorrect gear up command after takeoff December 27 2018 Release version 1.18b14 ======================================== - Fixed VNAV crash - Fixes for ATC error and XPDR display blanking December 26 2018 Release version 1.18b13 ======================================== - Adjusted fuel tank sizes - Updated open climb logic for short altitude deltas December 24 2018 Release version 1.18b12 ======================================== - Added possibility to enter waypoint on T/C and T/D markers - Fixed XPDR 1 power failure should allow usage of XPDR 2 December 21 2018 Release version 1.18b11 ======================================== - Allow LATREV from discontinuity - Fix for sound addons having incorrect triggers December 18 2018 Release version 1.18b10 ======================================== - Fixes for BGL scanning of p3d v3 scenery files December 17 2018 Release version 1.18b9 ======================================= - Added MCDU brightness keys - L/DEV scale now available during RNAV sids - Added non cancellable ECAM items - Improved BGL extraction to prevent airports without runways December 14 2018 Release version 1.18b8 ======================================= - FMS will now update the calculated position of altitude pseudo waypoints to make sure they are sequenced correctly - Fixed ND zoom factor during FCU 1+2 fault December 10 2018 Release version 1.18b7 ======================================= - Fixed incorrect gear up command after takeoff - Updated stall warning system December 9 2018 Release version 1.18b6 ====================================== - Updated ECAM for hung start - Prevent APPR button from activating an ILS approach if LOC signal is received on radio when ILS was not manually tuned December 6 2018 Release version 1.18b5 ====================================== - Updated overhead graphics - More protection against spurious speed callouts December 4 2018 Release version 1.18b4 ====================================== - Updated upper limit of ECON speed range when speed restriction is active - Fixed inproper VNAV data when flightplan is very short and T/C overlaps T/D November 30 2018 Release version 1.18b3 ======================================= - Fixes for PFD overlapping data and V/DEV L/DEV scales November 28 2018 Release version 1.18b2 ======================================= - Vnav and label fixes November 26 2018 Release version 1.18b1 ======================================= - Vnav fixes - Added missing L/DEV label - Fixed Poldragonet XPDR 1/2 switch reversal - Fixed issues with manually tuning VOR stations on RMP November 23 2018 Release version 1.17 ===================================== FMS: - Added support for const mach segments - Added step alts - Revised conditions for arming ILS approach instead of RNAV approach - RNAV approach arming now causes selected vertical mode to switch to managed mode - Fixes for FMS phase transitions and FMA modes during takeoff - Fix for crash when passing waypoints on longitude 0 - Make sure FCU heading is synchronized before disconnecting flight modes - Fixed increasing FCU alt during open climb or V/S does not increase cruise alt Systems: - Update to RMP SEL light logic - Fixed MCDU SP key not working when using ProSimA322 System driver - Added failures for ECAM fuel advisories - Fixes in FWC emulator to prevent a reported freeze during flight - Redefinition of FMS phase transitions to CLB for speedmanagement during single engine flight - Do not flash LVR MCT before green dot speed during single engine go around - Added autoland test button - Fixed Thrust rating shown too early during engine start Displays: - Updates to N1 gauge Flight guidance: - Added dampening for alpha protection speeds Hardware: - Fixed crash with Poldragonet driver when no mapping is present - Added support for Skalarki RMP SEL light CDU: - Fixed overwriting computed block fuel does not work - Fixed MCDU PBD entry no longer working - INIT page should allow entering of cruise temp - Added "Revert to..." naming to HOLD page and fixed colors of fields - Added slope to NAVRAD page November 21 2018 Release version 1.17b9 ======================================= - Update to RMP SEL light logic - Fixed MCDU SP key not working when using ProSimA322 System driver - Revised conditions for arming ILS approach instead of RNAV approach - RNAV approach arming now causes selected vertical mode to switch to managed mode November 17 2018 Release version 1.17b8 ======================================= - Added failures for ECAM fuel advisories - Fixes in FWC emulator to prevent a reported freeze during flight November 15 2018 Release version 1.17b7 ======================================= - Fixes for FMS phase transitions and FMA modes during takeoff November 14 2018 Release version 1.17b6 ======================================= - Fixed crash with Poldragonet driver when no mapping is present November 13 2018 Release version 1.17b5 ======================================= - Fixed MCDU PBD entry no longer working - Fixed overwriting computed block fuel does not work - Added support for Skalarki RMP SEL light - INIT page should allow entering of cruise temp - Redefinition of FMS phase transitions to CLB for speedmanagement during single engine flight - Added "Revert to..." naming to HOLD page and fixed colors of fields November 11 2018 Release version 1.17b4 ======================================= - Fix for crash when passing waypoints on longitude 0 - Added dampening for alpha protection speeds November 9 2018 Release version 1.17b3 ====================================== - Fix for crash during flight November 5 2018 Release version 1.17b2 ====================================== - Added support for const mach segments - Added slope to NAVRAD page - Added step alts October 29 2018 Release version 1.17b1 ==================================== - Make sure FCU heading is synchronized before disconnecting flight modes - Updates to N1 gauge - Do not flash LVR MCT before green dot speed during single engine go around - Fixed increasing FCU alt during open climb or V/S does not increase cruise alt - Added autoland test button - Fixed Thrust rating shown too early during engine start October 26 2018 Release version 1.16 ==================================== FMS: - Added support for along track waypoints - Added MCDU support for time markers - Added support for block type altitude constraint - PFD target alt should not show runway threshold alt during RNAV approach - Fixed aircraft not descending when pushing FCU ALT during cruise - VNAV descend fixes - Managed descend should ignore FCU ALT when FINAL APP armed - Fixed DIR to FROM point creates discontinuity - Added FMS Engine Out mode - Do not activate go around mode when levers moved into TOGA during engine failure at FLX takeoff - Fixed FMS managed speed mode during engine failure in NAV mode - Fix situation where managed vertical mode is armed when no managed vertical mode is active Systems: - Added fuel over/under temperature failures - Added hung start - Fixed ground steering issues with nosewheel steering disabled - Switch only outer DU between PFD/ND with XFER switch when ECAM switching state is not in normal position - Fixed fuel cross feed ECAM memo - Added fire indication due to loop failure - ECAM ignition message should not appear when engine anti ice switch is on Displays: - Fixes to ECAM pages - Updates size of fixes in ND - Added N1limit in upper ECAM - Added amber EGT limit in upper ECAM - Tuned ECAM ELEC page - Added Metric alt to lower ECAM - Fix Direct2D performance degradation after running for several hours - Reduced size of DME symbol in ND - Tuned ECAM visuals for FCTL - Chrono indication on ND should be white - Fixed DME only stations not shown with EFIS VOR button - Fixed ND not showing CSTR on waypoints when CSTR function is on and lateral mode is not managed - Improvement in ND descend marker during selected modes Hardware: - Added missing ACP switches and ACP3 for Poldragonet hardware - Added reading light support for Poldragonet hardware - Added support for Poldragonet sidestick and tiller hardware - Fixed Poldragonet XPDR does not show test pattern during light test CDU: - Added MCDU ETT function - Fixes to font size in MCDU FPLN page - Added MCDU PROG REPORT page - Upgraded SELECTED NAVAIDS MCDU page Misc: - Fix issue with intercom latency increasing over time - Improved failure naming October 26 2018 Release version 1.16b14 ======================================= - Updates size of fixes in ND October 25 2018 Release version 1.16b13 ======================================= - Added fuel over/under temperature failures October 23 2018 Release version 1.16b12 ======================================= - Added N1limit in upper ECAM - Added amber EGT limit in upper ECAM - Added support for along track waypoints October 21 2018 Release version 1.16b11 ======================================= - Tuned ECAM ELEC page - Added support for block type altitude constraint - Added hung start October 18 2018 Release version 1.16b10 ======================================= - PFD target alt should not show runway threshold alt during RNAV approach - Fixed ground steering issues with nosewheel steering disabled October 17 2018 Release version 1.16b9 ====================================== - Added MCDU ETT function - Fixes to font size in MCDU FPLN page October 15 2018 Release version 1.16b8 ====================================== - Fixes to ECAM pages - Added Metric alt to lower ECAM - Added MCDU support for time markers - Fix issue with intercom latency increasing over time October 12 2018 Release version 1.16b7 ====================================== - Switch only outer DU between PFD/ND with XFER switch when ECAM switching state is not in normal position - Fix Direct2D performance degradation after running for several hours - Improved failure naming October 10 2018 Release version 1.16b6 ====================================== - Fixed fuel cross feed ECAM memo - Reduced size of DME symbol in ND - Fixed aircraft not descending when pushing FCU ALT during cruise October 9 2018 Release version 1.16b5 ===================================== - Added MCDU PROG REPORT page - Added fire indication due to loop failure - Tuned ECAM visuals for FCTL - Chrono indication on ND whould be white - Fixed DME only stations not shown with EFIS VOR button - VNAV descend fixes - Managed descend should ignore FCU ALT when FINAL APP armed October 8 2018 Release version 1.16b4 ===================================== - Fixed DIR to FROM point creates discontinuity - Fixed ND not showing CSTR on waypoints when CSTR function is on and lateral mode is not managed - Upgraded SELECTED NAVAIDS MCDU page October 4 2018 Release version 1.16b3 ===================================== - ECAM ignition message should not appear when engine anti ice switch is on - Improvement in ND descend marker during selected modes October 1 2018 Release version 1.16b2 ===================================== - Added FMS Engine Out mode - Do not activate go around mode when levers moved into TOGA during engine failure at FLX takeoff - Fixed FMS managed speed mode during engine failure in NAV mode - Added missing ACP switches and ACP3 for Poldragonet hardware - Added reading light support for Poldragonet hardware September 29 2018 Release version 1.16b1 ======================================== - Added support for Poldragonet sidestick and tiller hardware - Fixed Poldragonet XPDR does not show test pattern during light test - Fix situation where managed vertical mode is armed when no managed vertical mode is active September 27 2018 Release version 1.15 ====================================== FMS: - Fixed V/DEV missing during raw data flight - V/DEV in PROG page should remain visible during descend and approach FMS phase - Automatic selection of NONE for VIA or transition if none available. - Fixed issue where altitude flyover waypoints after takeoff were bypassed Systems: - Fixed Hyd pump FAULT light not illuminating when resevoir overheats - Single elev fault due to hyd loss should not cause alternate law - Fixed nose wheel steering available when steering pin inserted - Fixed triple click for capability change while ILS not received - Added failures for reactive windshear detection - Added XPDR 1 and XPDR 2 ECAM procedures - Added stuck mic failures - Rewired signals through SDAC so ECAM responds correct to SDAC failures Displays: - Improvements in PFD pitch scale - Improvements in ECAM fuel page for FQI faults Flight guidance: - Improved autopilot handling to prevent oscillations - Fixed LOC mode not available during RA 1+2 failure - Improvements of elevator control in extreme pitch conditions Hardware: - Added missing Skalarki ACP panel switches - Added support for FSCockpit ACP INT/RAD switch CDU: - Fixed Vls disappears when manually enter Vapp - Fix NAVRAD page should filter navaid types when entering names in VOR or ADF fields Misc: - Fixed Right wing doors named incorrectly - Fixed terrain database not downloading correctly - Fixed RMP NAV tuning of course not working - Added SDK output of sidestick forces - Navaid virtualization is now enabled when the installed AIRAC database supports it. The status of navaid virtualization is shown in the "Database" part of the "Software" block in ProSimA322-system. If enabled, all navaid signals are now generated based on AIRAC data, instead of scenery in Prepar3d. Support for virtualization is available by downloading the latest AIRAC database from Navigraph. September 26 2018 Release version 1.15b12 ========================================= - Added missing Skalarki ACP panel switches September 26 2018 Release version 1.15b11 ========================================= - Fixed V/DEV missing during raw data flight - Improved autopilot handling to prevent oscillations September 24 2018 Release version 1.15b10 ========================================= - Fixed Right wing doors named incorrectly - Fixed terrain database not downloading correctly September 20 2018 Release version 1.15b9 ======================================== - V/DEV in PROG page should remain visible during descend and approach FMS phase - Automatic selection of NONE for VIA or transition if none available. - Fixed Hyd pump FAULT light not illuminating when resevoir overheats - Fixed Vls disappears when manually enter Vapp September 18 2018 Release version 1.15b8 ======================================== - Single elev fault due to hyd loss should not cause alternate law - Fixed LOC mode not available during RA 1+2 failure - Improvements of elevator control in extreme pitch conditions - Fixed nose wheel steering available when steering pin inserted - Fixed RMP NAV tuning of course not working September 14 2018 Release version 1.15b7 ======================================== - Improvements in PFD pitch scale - Improvements in ECAM fuel page for FQI faults September 12 2018 Release version 1.15b6 ======================================== - Fix NAVRAD page should filter navaid types when entering names in VOR or ADF fields - Fixed virtualized vor incorrect inclination used September 10 2018 Release version 1.15b5 ======================================== - Fixed triple click for capability change while ILS not received September 10 2018 Release version 1.15b4 ======================================== - Navaid virtualization is now optional an can be switched off in the cockpit setup menu of the IOS - Added failures for reactive windshear detection - Added SDK output of sidestick forces - Added XPDR 1 and XPDR 2 ECAM procedures September 5 2018 Release version 1.15b3 ======================================= - Navaid virtualization is now enabled when the installed AIRAC database supports it. The status of navaid virtualization is shown in the "Database" part of the "Software" block in ProSimA322-system. If enabled, all navaid signals are now generated based on AIRAC data, instead of scenery in Prepar3d. Support for virtualization is available by downloading the latest AIRAC database from Navigraph. - Added stuck mic failures September 4 2018 Release version 1.15b2 ======================================= - Fixed issue where altitude flyover waypoints after takeoff were bypassed September 3 2018 Release version 1.15b1 ======================================= - Added support for FSCockpit ACP INT/RAD switch - Rewired signals through SDAC so ECAM responds correct to SDAC failures August 31 2018 Release version 1.14 =================================== First release with support for hardware accelerated displays. This option is off by default. It is found in the ProSim Display configuration screen. To enable experimental hardware acceleration, enable the option "Use direct2d" and restart ProSimDisplay. FMS: - Approach mode not available if RA 1+2 failed - FMGC will now ignore entering of duplicate waypoint - Check for higher cruise alt even for open climb - Added SPD SEL flag support Systems: - Fuel MODE SEL switch swapped around to pressed state is the auto state - Added windshear detection to FAC - Fix flightsurface not moving if controller operational but not powered - Fixed ECAM status inop sys for RA 1+2 failure - Add missing ACP lights, switches and buttons - Fixed DOOR ECAM message not functioning when door failure used - Fixed issue with bouncing air pressure on ground after reposition - Fixed after inflight engine start, engines are only available after full start - Fixed CAT 1 capability not activating when only one PFD is visible - Don't show TA ONLY message if switch not in TA/RA position and on the ground - Added FDUs - Fixed altn brk fault when parking brake is on during cold and dark startup - Tuning of system startup times - Added fire loop testing - Added FMGC1 C/B - Added sidestick reversion failures - Start pack inhibit as soon as engine mode switch is set to Start - Fixed Pack flow valve to be springloaded so it shows uncommanded position when bleed air pressure low Displays: - Update Display with new fonts and new text handling code - Tuning of upper ECAM flap block display - Don't show wind arrow on ND below 100 kts - Extended drawing region for ND PLAN mode - Several weather radar fixes - Improvements to ND ILS display - Fixed alignment of FMA first column - Refined conditions for displaying GLoad on lower ECAM - Fixed FMA FLX takeoff missing + sign - Fix for misalignment of text with gray background - Fixed ECAM Wheel nose wheel steering hydraulic system label does not update when configuration changes between green and yellow source Flight guidance: - Fixed some misaligned ILS approaches. Data was read from the navigation database, instead of the installed scenery, which could cause some misalignments - TCAS mode now first gets armed during a TCAS TA situation - Enable autothrottle to be armed with levers at idle in the air - Added reversion mode for level off before thrust reduction altitude Hardware: - Fixed reversal of ADR2 and ADR3 switches and indicators for FSCockpit hardware - Fixed rudder trim display to display single digit when value below 10 - Added sycnhronised blinked of warning lights to prevent auto of sync blinking between left and right CDU: - Report approach descend angles in MCDU FLPN, where available in navigation database - Added missing * to MCDU DUPLICATE NAMES page - Allow entry of 360 degrees in MCDU - CRS clears when new VOR is entered in RAD NAV page - Added Generic TCP driver to MCDU - Added screen content of MCDUs to SDK - Fixed distance to destination (last line on FPLN MCDU page) not displaying correctly when route is not yet completed Misc: - Fixed removing C/B failure in IOS does not reset the C/B - Changed failure name for pump overheat to elec pump overheat - Fixed Hardware conversion settings not working when setting switch through SDK August 28 2018 Release version 1.14b15 ====================================== - Fuel MODE SEL switch swapped around to pressed state is the auto state - Added windshear detection to FAC - Fixed removing C/B failure in IOS does not reset the C/B August 26 2018 Release version 1.14b14 ====================================== - Fix flightsurface not moving if controller operational but not powered - Tuning of upper ECAM flap block display - First release of virtualisation of NAV sources. We will no longer rely on the backend simulator for providing radio signals in the future, so we can deliver an up to date navigation environment based on AIRAC data instead of potentially outdated scenery. This feature is not enabled by default and we are still talking to Navigraph for required data. August 22 2018 Release version 1.14b13 ====================================== - Fix for crash in MCDU August 22 2018 Release version 1.14b12 ====================================== - Fixed ECAM status inop sys for RA 1+2 failure - Approach mode not available if RA 1+2 failed - Add missing ACP lights, switches and buttons - Fixed DOOR ECAM message not functioning when door failure used - Don't show wind arrow on ND below 100 kts - Extended drawing region for ND PLAN mode - Report approach descend angles in MCDU FLPN, where available in navigation database August 21 2018 Release version 1.14b11 ====================================== - Display: several weather radar fixes - Fixed issue with bouncing air pressure on ground after reposition - Added missing * to MCDU DUPLICATE NAMES page - Allow entry of 360 degrees in MCDU - Fixed reversal of ADR2 and ADR3 switches and indicators for FSCockpit hardware August 19 2018 Release version 1.14b10 ====================================== - Fixed after inflight engine start, engines are only available after full start - Update Display with new fonts and new text handling code - FMGC will now ignore entering of duplicate waypoint - Add ability to disable ClearType with Direct2D - High Quality Text is now always enabled with Direct2D - Add experimental outlining option to Direct2D mode (supports font hinting and antialiasing) - Improvements to ND ILS display August 19 2018 Release version 1.14b9 ===================================== - Fixed CAT 1 capability not activating when only one PFD is visible - Don't show TA ONLY message if switch not in TA/RA position and on the ground August 14 2018 Release version 1.14b8 ===================================== - Fixed some misaligned ILS approaches. Data was read from the navigation database, instead of the installed scenery, which could cause some misalignments August 13 2018 Release version 1.14b7 ===================================== - Fixed rudder trim display to display single digit when value below 10 - Changed failure name for pump overheat to elec pump overheat - Tuning of system startup times - Added FDUs - TCAS mode now first gets armed during a TCAS TA situation August 12 2018 Release version 1.14b6 ===================================== - Fixed alignment of FMA first column - Fixed altn brk fault when parking brake is on during cold and dark startup - CRS clears when new VOR is entered in RAD NAV page - Changed boot time of FWC and SDCU - Added fire loop testing August 11 2018 Release version 1.14b5 ===================================== - Enable autothrottle to be armed with levers at idle in the air - Check for higher cruise alt even for open climb - Added SPD SEL flag support - Added FMGC1 C/B - Added sidestick reversion failures - Refined conditions for displaying GLoad on lower ECAM - Added reversion mode for level off before thrust reduction altitude August 7 2018 Release version 1.14b4 ==================================== - Start pack inhibit as soon as engine mode switch is set to Start - Added sycnhronised blinked of warning lights to prevent auto of sync blinking between left and right - Fixed FMA FLX takeoff missing + sign August 7 2018 Release version 1.14b3 ==================================== - Fix for misalignment of text with gray background - Fix fo issue with calculation of T/D that was introduced in 1.14b2 August 6 2018 Release version 1.14b2 ==================================== - Fixed Hardware conversion settings not working when setting switch through SDK - Added Generic TCP driver to MCDU - Added screen content of MCDUs to SDK - Fixed distance to destination (last line on FPLN MCDU page) not displaying correctly when route is not yet completed - Fixed Pack flow valve to be springloaded so it shows uncommanded position when bleed air pressure low August 3 2018 Release version 1.14b1 ==================================== - Fixed ECAM Wheel nose wheel steering hydraulic system label does not update when configuration changes between green and yellow source - New experimental hardware accelerated rendering available as option in ProSimDisplay August 2 2018 Release version 1.13 ================================== FMS: - Added option to engage NAV instead of GA TRK for go around - Fixed MDA references radio alt intead of air data - Speed and altitude stability improvements for managed flight - Improved overspeed logic of managed descend - Fixed APP NAV mode not capturing NPA descend - Improved isa calculation to use tropopause - Improvements in MCDU direct to handling Systems: - Added GPS fault ECAM procedure - Added VHF/HF transmission ECAM - Added sys page call inhibit - Added AP/ATHR failures - Added C/B popping to IOS Displays: - Improved appearance of PFD FPV - Improved blinking of E/WS Idle string Flight guidance: - Fixed FCU speed may show 0 when pulling speed knob on ground - Fixed FCU V/S may reset to current V/S when pushing and pulling knob - Lat managed dot should be on when loc/gs armed - Fixed stability issue with roll rate - Fix FCU doing incorrect conversions when trackmode is written with same value through SDK Hardware - Added FDS FCU extra layout option for FD/LS swapped CDU: - Revised MCDU approach/departure RETURN/RETURN END - Changed in layout to departure/arrival pages and selection of NONE for arrivals/via's - Split Thr red alt/accel alt/eoaccel alt for takeoff and GA phases - Improvements in changing TO waypoint in CDU - Added INIT A Gnd Temp - Cosmetic changes to CDU pages Misc: - Added FWC reset to IOS - ADR Fault buttons renamed in IOS - Added Adiru SDK variables August 1 2018 Release version 1.13b11 ===================================== - Improved appearance of PFD FPV - Revised MCDU approach/departure RETURN/RETURN END - Added FWC reset to IOS July 30 2018 Release version 1.13b10 ==================================== - ADR Fault buttons renamed in IOS - Added GPS fault ECAM procedure - Changed in layout to departure/arrival pages and selection of NONE for arrivals/via's July 30 2018 Release version 1.13b9 =================================== - Added option to engage NAV instead of GA TRK for go around - Fixed MDA references radio alt intead of air data - Split Thr red alt/accel alt/eoaccel alt for takeoff and GA phases - Speed and altitude stability improvements for managed flight July 26 2018 Release version 1.13b8 =================================== - Improved overspeed logic of managed descend July 23 2018 Release version 1.13b7 =================================== - Added FDS FCU extra layout option for FD/LS swapped - Added Adiru SDK variables - Fixed APP NAV mode not capturing NPA descend July 19 2018 Release version 1.13b6 =================================== - Added additional SDK data for ADIRU - Improved isa calculation to use tropopause July 15 2018 Release version 1.13b5 =================================== - Fixed FCU speed may show 0 when pulling speed knob on ground - Fixed FCU V/S may reset to current V/S when pushing and pulling knob - Improved blinking of E/WS Idle string - Lat managed dot should be on when loc/gs armed - Added sys page call inhibit - Added VHF/HF transmission ECAM July 12 2018 Release version 1.13b4 =================================== - Added Adirus data to SDK - Fixed stability issue with roll rate - Added AP/ATHR failures July 12 2018 Release version 1.13b3 =================================== - Improvements in MCDU direct to handling - Improvements in changing TO waypoint in CDU - Added INIT A Gnd Temp July 8 2018 Release version 1.13b2 ================================== - Cosmetic changes to CDU pages - Added C/B popping to IOS July 6 2018 Release version 1.13b1 ================================== - Fix FCU doing incorrect conversions when trackmode is written with same value through SDK - Fix for crash in ProSimDisplay July 5 2018 Release version 1.12 ================================ FMS: - Adjusted selected speed change over threshold - Changed FCU minimum selectable altitude in 1000 feet mode to 100 feet - Fixed incorrect trip/time time field - Fixes for flightplan sequencing during go around - Added VNAV altitude errors - Selecting a new approach should clear entered MDA Systems: - Fixed start fault appearing after engine failure - Fixed CPC1 fault calling incorrect ECAM page - Added individual tank pump pressure ECAM faults - Added NORMAL message after pressing RCL on upper ecam - STS NORMAL message should only appear temporarily - Added specific SDAC functionality - Updated engine start valve display to disappear after 2nd engine start - Fixed RA invalid signal not functioning when RA are unpowered - Fixed upper ecam display duplicated on lower ecam for too long after emergency generator recovers power - Fixes for FCU 1+2 fault - Fixed wrong fuel flow indications during engine start - Refined alternate law conditions due to slats locked - Added options for fire failures requiring 1 or 2 bottles to extinguish Displays: - Fixed TAS and Wind information on ND only shown above certain speeds - Fixed weather radar tilt was always positive - Added A FLOOR indication to upper ECAM - Do not show PFD VDEV when glideslope hold is active Flight guidance: - Fix for HDG mode not following preselected heading after discontinuity - Improved pitch stability in manual flight Hardware - Added support for poldragonet C/B panel - Fixed IOCP MCDU mappings - Added missing MCDU MENU key mapping to IOCP MCDU driver - Added discrete switch input for weather radar gain - Added poldragonet dome light and reading light support CDU: - Added descend angle to FLPN MCDU page - Added CHECK MIN DEST FOB message - Added TOO STEEP PATH fpln line - Added MORE DRAG message Misc: - Added RDME flags for individual radios to SDK - Added RDME powered dataref to SDK - Added SDK variables to control FCU/EFIS states directly - Added RDME VOR/ADF raw data July 2 2018 Release version 1.12b10 =================================== - Fixed CPC1 fault calling incorrect ECAM page - Fix for HDG mode not following preselected heading after discontinuity - Added support for poldragonet C/B panel - Adjusted selected speed change over threshold - Added RDME flags for individual radios to SDK June 26 2018 Release version 1.12b9 =================================== - Added SDK variables to control FCU/EFIS states directly - Added individual tank pump pressure ECAM faults - Added NORMAL message after pressing RCL on upper ecam - STS NORMAL message should only appear temporarily June 26 2018 Release version 1.12b8 =================================== - Added specific SDAC functionality - Fixed TAS and Wind information on ND only shown above certain speeds June 25 2018 Release version 1.12b7 =================================== - Changed FCU minimum selectable altitude in 1000 feet mode to 100 feet - Added RDME powered dataref to SDK - Updated conditions for RDME flags June 22 2018 Release version 1.12b6 =================================== - Retuned auto changeover in selected speed mode - Improved pitch stability in manual flight - Fixed weather radar tilt was always positive June 19 2018 Release version 1.12b5 =================================== - Updated engine start valve display to disappear after 2nd engine start - Fixed RA invalid signal not functioning when RA are unpowered - Fixed upper ecam display duplicated on lower ecam for too long after emergency generator recovers power - Fixes for FCU 1+2 fault - Fixed wrong fuel flow indications during engine start - Fixed incorrect trip/time time field - Added RDME VOR/ADF raw data June 19 2018 Release version 1.12b4 =================================== - Fixed IOCP MCDU mappings June 19 2018 Release version 1.12b3 =================================== - Added descend angle to FLPN MCDU page - Refined alternate law conditions due to slats locked - Added A FLOOR indication to upper ECAM - Added missing MCDU MENU key mapping to IOCP MCDU driver June 15 2018 Release version 1.12b2 =================================== - Do not show PFD VDEV when glideslope hold is active - Fixes for flightplan sequencing during go around June 12 2018 Release version 1.12b1 =================================== - Added discrete switch input for weather radar gain - Added options for fire failures requiring 1 or 2 bottles to extinguish - Added VNAV altitude errors - Added CHECK MIN DEST FOB message - Added TOO STEEP PATH fpln line - Added MORE DRAG message - Added poldragonet dome light and reading light support - Selecting a new approach should clear entered MDA June 7 2018 Release version 1.11 ================================ !! Four switches on the ELEC panel were changed from latched to momentary. Please check the switch types tab in the configuration screen and verify your hardware settings. The switches are: Commercial, Galy Cab, AC Ess Feed, Bus tie FMS: - Fixes for init fuel page - Fixes to ALTN fuel calculations - Changing destination will now clear alternate - Fix for incorrect NAV intercepts on NAV activation - VNAV fixes for speed control - VNAV fixes for flight withouth cruise alt - Overspeed protection should only occur at VMO/MMO not at VMax - Fixed NAV remaining on when encountering a discontinuity - Fixed VNAV distance discrepancies after a NAV intercept Systems: - Added failure for low crew oxygen and pressure valve - Fix rudder trim reset to 0 when A/P engaged - Changed pressurisation arrow to show actual cabin V/S direction instead of CPC mode - Added option for AC Essential feed auto switching - A/T should disenaged immediately after loss of 2 ADR's - Added labels to ECAM pressure page for CPC failures - Altn Law during WTB only when slats are locked outside of 0 degrees - Added APU low oil level failure - Added engine oil high warnings and advisories - Fix for FWC status page during FWC 1+2 fault - Fixed TA ONLY message not showing when TCAS mode set to TA - Fix for incorrect rotation of ground radar in all display modes - Improve reverser control through LGCUI signals - Automatic toggle LGCUI master of active system is unavailable Displays: - New ProSimDisplay rendering layer. This is the first phase of upgrading ProSimDisplay to support hardware rendering. - Improved layout of navaid data (Symbol, ID, DME) in ND - Added lighttest functionality to PFD/ND - Changed go around line color to cyan instead of blue - Fixed engine time trends showing up on shutdown engine - Added option for green vertical deviation indicator Flight Guidance: - FD pushbutton has to be used to disabled FD light in case FD becomes unavailable - Fixed Alt CRZ* should be ALT* - Fixed NAV mode engaging while aircraft is too far away - Heading can now be preselected before NAV disconnect - Retuned rudder ground control - Improved yaw bar - Fix for discrepancy between rudder trim and rudder Hardware: - Fixed poldragonet light bright/dim mixed up CDU: - Added continous scrolling of FPLN page - Fixed ND not scrolling in plan mode with SEC FPLN - FPLN page now uses TIME instead of UTC on ground - Fixed changing ACCEL ALT should not affect EO ACCELT ALT - Adjusted max alt and opt alt in single engine flight Misc: - Cabin pressure is now reset to appropriate values when a reposition occurs June 5 2018 Release version 1.11b13 =================================== - Fixes to ALTN fuel calculations - Changing destination will now clear alternate June 4 2018 Release version 1.11b12 =================================== - Fixes for init fuel page - Fix for incorrect NAV intercepts on NAV activation - FPLN page now uses TIME instead of UTC on ground June 2 2018 Release version 1.11b11 =================================== - VNAV fixes for speed control - Fixed ND not scrolling in plan mode with SEC FPLN - Fixed changing ACCEL ALT should not affect EO ACCELT ALT June 1 2018 Release version 1.11b10 =================================== - Fixed crew oxygen pressure indicator sensor should be upstream of valve - FD pushbutton has to be used to disabled FD light in case FD becomes unavailable - Added lighttest functionality to PFD/ND - Fixed Alt CRZ* should be ALT* - Fixed NAV mode engaging while aircraft is too far away May 31 2018 Release version 1.11b9 ================================== - VNAV fixes for flight withouth cruise alt - Fix rudder trim reset to 0 when A/P engaged May 30 2018 Release version 1.11b8 ================================== - Overspeed protection should only occur at VMO/MMO not at VMax - Heading can now be preselected before NAV disconnect - Retuned rudder ground control May 29 2018 Release version 1.11b7 ================================== - Fixed poldragonet light bright/dim mixed up - Changed pressurisation arrow to show actual cabin V/S direction instead of CPC mode - Changed go around line color to cyan instead of blue - Fixed NAV remaining on when encountering a discontinuity May 28 2018 Release version 1.11b6 ================================== - Fix for discrepancy between rudder trim and rudder - Adjusted max alt and opt alt in single engine flight May 27 2018 Release version 1.11b5 ================================== - Fixed engine time trends showing up on shutdown engine - Added option for AC Essential feed auto switching - A/T should disenaged immediately after loss of 2 ADR's - Four switches on the ELEC panel were changed from latched to momentary. Please check the switch types tab in the configuration screen and verify your hardware settings. The switches are: Commercial, Galy Cab, AC Ess Feed, Bus tie May 26 2018 Release version 1.11b4 ================================== - New ProSimDisplay rendering layer. This is the first phase of upgrading ProSimDisplay to support hardware rendering. - Added failure for low crew oxygen and pressure valve - Added labels to ECAM pressure page for CPC failures - Cabin pressure is now reset to appropriate values when a reposition occurs - Altn Law during WTB only when slats are locked outside of 0 degrees - Added APU low oil level failure - Added engine oil high warnings and advisories May 23 2018 Release version 1.11b3 ================================== - Improved layout of navaid data (Symbol, ID, DME) in ND - Automatic toggle LGCUI master of active system is unavailable - Improved yaw bar - Improve reverser control through LGCUI signals - Automatic toggle LGCUI master of active system is unavailable May 21 2018 Release version 1.11b2 ================================== - Added continous scrolling of FPLN page - Fix for FWC status page during FWC 1+2 fault - Fixed TA ONLY message not showing when TCAS mode set to TA May 17 2018 Release version 1.11b1 ================================== - Fix for incorrect rotation of ground radar in all display modes May 16 2018 Release version 1.10 ================================ FMS: - ALT CRZ now available in selected mode - Engine limits revised - FCU altitude maximum changed to 49000 - FCU FPA range changed to -9.9 to 9.9 - LNAV/VNAV improvements - Improved FLPN restringing - Improved LNAV rendering - Fixed NAV not disconnecting when discontinuity encoutered Systems: - Improved brake temperature model - Improvements to brake fans - Added EIU failure simulation - Improved APU bleed pressure values - Fixed missing THR LEVERS NOT SET message if TLA is at MCT with no FLEX temperature inserted - Retuned APU fuel flow - Hydraulic leaks now cause low pressure - Open doors affect inside pressure - Switch CPC master system when pressurisation in manual mode for 10 seconds - Fixed bleed air valves not closing when upstream pressure is low - Improvements to igniter selection Displays: - Fixed magnetic variation issue in terrain/weather radar - Sidestick position only available after engine start - E/WD offline data now shown in amber instead of red - Improvements to ECAM bleed page - Elec generator should show 0 hz instead of xxx hz - Fix for PFD speedtape - Added energy circle to ND - Tuned PFD VMAX representation on speedtape - Fixed ND showing cstr data without showing waypoints in go-around segments - ND should only render missed approach/alternate when in view in CDU Flight guidance: - Fixed vertical speed accuracy - Allow G/S capture during LOC* Hardware: - Added Intercom - Fixed reversal of ND inner and outer analog controls - Added support for augmentation to rudder input - Added gates for 80kts and 100kts callouts Misc: - Moved "alternate brake option" in cockpit setup to "Steering system on yellow hyd". This will now move the NWS to yellow hyd. - Passenger weight increased to average of 88kg - Added CDU ground service menu - New Simconnect interface library May 16 2018 Release version 1.10b19 =================================== - Fixed magnetic variation issue in terrain/weather radar May 15 2018 Release version 1.10b18 =================================== - More Simconnect test logging - Improvements to brake fans May 14 2018 Release version 1.10b17 =================================== - Improved brake temperature model - Fixed vertical speed accuracy May 10 2018 Release version 1.10b16 =================================== - Fixed master 2 switch not working May 10 2018 Release version 1.10b16 =================================== - Fixed master 2 switch not working May 10 2018 Release version 1.10b15 =================================== - Added EIU failure simulation May 9 2018 Release version 1.10b14 ================================== - Improved APU bleed pressure values - Fixed reversal of ND inner and outer analog controls - Fixed missing THR LEVERS NOT SET message if TLA is at MCT with no FLEX temperature inserted May 8 2018 Release version 1.10b13 ================================== - Sidestick position only available after engine start - Retuned APU fuel flow - E/WD offline data now shown in amber instead of red - ALT CRZ now available in selected mode - Engine limits revised May 6 2018 Release version 1.10b12 ================================== - Hydraulic leaks now cause low pressure - Improvements to ECAM bleed page - Open doors affect inside pressure - Switch CPC master system when pressurisation in manual mode for 10 seconds - Allow G/S capture during LOC* - Elec generator should show 0 hz instead of xxx hz - Moved "alternate brake option" in cockpit setup to "Steering system on yellow hyd". This will now move the NWS to yellow hyd. - Added support for augmentation to rudder input - FCU altitude maximum changed to 49000 - FCU FPA range changed to -9.9 to 9.9 - Passenger weight increased to average of 88kg May 3 2018 Release version 1.10b11 ================================== - Added CDU ground service menu - VNAV fixes - Fixed bleed air valves not closing when upstream pressure is low - Improvements to igniter selection April 30 2018 Release version 1.10b10 ==================================== - Improved feature detection code April 27 2018 Release version 1.10b9 ==================================== - Fixes to intercom system - LNAV/VNAV improvements April 25 2018 Release version 1.10b8 ==================================== - Improved FLPN restringing - New Simconnect interface library - Fixes to intercom system April 24 2018 Release version 1.10b7 ==================================== - Intercom stability improvements April 24 2018 Release version 1.10b6 ==================================== - Fix for PFD speedtape April 23 2018 Release version 1.10b5 ==================================== - Improved process timers - Added Intercom April 23 2018 Release version 1.10b4 ==================================== - Added energy circle to ND - Added gates for 80kts and 100kts callouts - Tuned PFD VMAX representation on speedtape - Fix for ProSimAudio not updating April 22 2018 Release version 1.10b3 ==================================== - Fix for ProsimAudio issues - Improved LNAV rendering April 21 2018 Release version 1.10b2 ==================================== - Fix for ProsimAudio issues - Fixed ND showing cstr data without showing waypoints in go-around segments April 20 2018 Release version 1.10b1 ==================================== - ND should only render missed approach/alternate when in view in CDU - Fixed NAV not disconnecting when discontinuity encoutered April 17 2018 Release version 1.09 ================================== - Added background loading of database - Added DATA 2/2 Navaids page - Fixed ND crash (white box with red cross) when ILSDME navaid type is selected - Added TUNE xxx CDU message - Added analog element to allow numerical input for the RMP course value - Added localiser/glideslope failures - CRZ ALT reset on activation of approach phase - Added new configuration screen tab for hardware configuration options - Added option to switch pitch load factor to realistic more sensitive configuration - Updates overhead panel graphics - Improvements in roll response - Added aircraft.engines.limits namespace to SDK for engine N1 limits April 17 2018 Release version 1.09b4 ==================================== - Added background loading of database April 16 2018 Release version 1.09b3 ==================================== - Added DATA 2/2 Navaids page April 14 2018 Release version 1.09b2 ==================================== - Fixed ND crash (white box with red cross) when ILSDME navaid type is selected - Added TUNE xxx CDU message - Added analog element to allow numerical input for the RMP course value - Added localiser/glideslope failures - CRZ ALT reset on activation of approach phase April 4 2018 Release version 1.09b1 =================================== - Added new configuration screen tab for hardware configuration options - Added option to switch pitch load factor to realistic more sensitive configuration - Updates overhead panel graphics - Improvements in roll response - Added aircraft.engines.limits namespace to SDK for engine N1 limits March 24 2018 Release version 1.08 ================================== This hotfix improves processing of licensing data to prevent errors that require manual action. - Updater also succeeds when system dlls are locked - Synchronize update subscriptions with server - Added support for FSCockpit PFD/ND v2 panels - Fixed G/S not disabled when lateral mode is changed from LOC - Added thrust not set ECAM warning - Fixed crash in DIR TO when Radial is entered without selecting DIR TO point March 21 2018 Release version 1.08b2 ==================================== - Added support for FSCockpit PFD/ND v2 panels March 20 2018 Release version 1.08b1 ==================================== - Fixed G/S not disabled when lateral mode is changed from LOC - Added thrust not set ECAM warning - Fixed crash in DIR TO when Radial is entered without selecting DIR TO point March 16 2018 Release version 1.07 ================================== FMS: - LNAV fixes - Fixed lnav sequencing waypoints too early when transition could not be calculateed correctly - Approach Vls is based on calculated landing weight when FMS phase is before approach - Fixed clearing of FPLN entry in LSK1L - NAV should be armed during DIR-TO, even if no nav intercept - Added FCU Freeze during ils approach - Added Approach data freeze - Improved NAV intercept function - Idle N1 scales dynamically based on engine anti ice valves - Fix for Vapp calculation with tower wind - Default trip wind should be headwind - Fixes for incorrect enroute distance calculations Systems: - Prevent yaw damper fault on ground before startup - Increased center tank low level signal to prevents center tank auto logic from running the pumps on an empty tank - Fix for A/P disconnect due to rudder trim - Fix for IDG oil ovht - Added ECAM fuel advisories - Fixed ADR Fault light when mode is OFF - Fix MCDU fail not working - Retuned elevator autotrim for better response - Retuned rudder travel limiter - Added APU bleed boost for engine start - Fixed representation and value if engine vibration - Fixed ENG SHutdown ECAM procedure did not request XPDR mode to TA - Fixed rudder trim limit too high - Fixed rudder control not visible when FACs are offline - Improvements in yellow brake system - Inhibit APU start in emergency elec config for 45 seconds - Limit APU start altitude in emergency elec config - Fixed FAC interfering with manual rudder input - Added ECP fault - ECAM pages should still be accessible with FWC 1+2 fault - Fixed range and steps of manual landing alt - Fixed FWC incorrectly activating phase 9 on takeoff momentarily, causing inhibited messages to appear - Added ECAM procedure for fuel auto transfer fault - Increased rudder trim reset speed Displays: - Reformatting of CTE on ND - Add speed constraints to EFIS CSTR display - Draw fuel line as continuous in ECAM FUEL page when crossfeed is open - V/DEV message should also appear when FINAL APP is armed - Improved ECAM FCTL elevator depiction - Lower ECAM should display ECAM ON ND message on transfer - Upgraded diagonal line to "INVALID DATA" for LCD type displays - Improvements in ECAM FCTL rudder display - Changed ND VOR mode HSI information to cyan - Ecam spd brk message in amber should blink - Status maintenance data should appear on bottom of status page - Fixed FMA boxes appearing when PFD is reinitialized because of screen change - Fixed fuel information quantized to 10 and 20kg intervals Flight guidance: - F/D should be inop with dual AC fault - SRS should remain engaged when engaging go-around above GA Accel alt Hardware: - Updated skalarki SDK - Fixed FSCockpit MCDU old layout slash and minus keys reversed - Fixed FDS XPDR more TA, TA/RA/ Standby not working properly - Fixed OVFY not working on FDS CDU - Added support for Poldragonet upper/lower ecam brightness, gravity gear extend and console/floor lights Misc: - Added muting capability to ProSimAudio. When pausing/freezing simulator, ProSimAudio will mute. - Added mute option to the IOS for manual mutting - Fixed approaches page not working with new navigraph airac cycle - Fixed FSUIPC version not showing corrrectly in UI - Fixed flood of FUEL_SELECTOR_SET and FUEL_SELECTOR_2_SET events in FSUIPC March 13 2018 Release version 1.07b16 ===================================== - Reformatting of CTE on ND - Prevent yaw damper fault on ground before startup - Updated skalarki SDK - Added muting capability to ProSimAudio. When pausing/freezing simulator, ProSimAudio will mute. - Added mute option to the IOS for manual mutting March 12 2018 Release version 1.07b15 ===================================== - Approach Vls is based on calculated landing weight when FMS phase is before approach - Increased center tank low level signal to prevents center tank auto logic from running the pumps on an empty tank - Add speed constraints to EFIS CSTR display - Draw fuel line as continuous in ECAM FUEL page when crossfeed is open March 9 2018 Release version 1.07b14 ==================================== - Fix for A/P disconnect due to rudder trim - Fix for IDG oil ovht - Added ECAM fuel advisories March 7 2018 Release version 1.07b13 ==================================== - Fixed approaches page not working with new navigraph airac cycle - Fixed ADR Fault light when mode is OFF -Fixed clearing of FPLN entry in LSK1L March 6 2018 Release version 1.07b12 ==================================== - V/DEV message should also appear when FINAL APP is armed - NAV should be armed during DIR-TO, even if no nav intercept - Added FCU Freeze during ils approach - Improved NAV intercept function March 5 2018 Release version 1.07b11 ==================================== - Fix MCDU fail not working - improved ECAM FCTL elevator depiction - fixed FSCockpit MCDU old layout slash and minus keys reversed - returned elevator autotrim for better response March 4 2018 Release version 1.07b10 ==================================== - Lower ECAM should display ECAM ON ND message on transfer - Upgraded diagonal line to "INVALID DATA" for LCD type displays - Added approach data freeze - Retuned rudder travel limiter - Improvements in ECAM FCTL rudder display - Idle N1 scales dynamically based on engine anti ice valves March 2 2018 Release version 1.07b9 =================================== - Cruise alt is cleared on initiating a go around - Add triple click warning for GPS PRIMARY LOST February 27 2018 Release version 1.07b8 ======================================= - Added APU bleed boost for engine start - Changed ND VOR mode HSI information to cyan - Fixed representation and value if engine vibration - fix for Vapp calculation with tower wind February 25 2018 Release version 1.07b7 ======================================= - Ecam spd brk message in amber should blink - Fixed ENG SHutdown ECAM procedure did not request XPDR mode to TA - Fixed FDS XPDR more TA, TA/RA/ Standby not working properly - Fixed rudder trim limit too high - Fixed rudder control not visible when FACs are offline - Improvements in yellow brake system - F/D should be inop with dual AC fault - Inhibit APU start in emergency elec config for 45 seconds - Limit APU start altitude in emergency elec config - Status maintenance data should appear on bottom of status page February 23 2018 Release version 1.07b6 ======================================= - Fixed FAC interfering with manual rudder input February 22 2018 Release version 1.07b5 ======================================= - Default trip wind should be headwind - Fixed OVFY not working on FDS CDU - Fixed FMA boxes appearing when PFD is reinitialized because of screen change - Added ECP fault - ECAM pages should still be accessible with FWC 1+2 fault - SRS should remain engaged when engaging go-around above GA Accel alt - Fixed fuel information quantized to 10 and 20kg intervals - Fixed range and steps of manual landing alt February 21 2018 Release version 1.07b4 ======================================= - Fixed FSUIPC version not showing corrrectly in UI - Fixed flood of FUEL_SELECTOR_SET and FUEL_SELECTOR_2_SET events in FSUIPC - LNAV fixes February 21 2018 Release version 1.07b3 ======================================= - Fixed lnav sequencing waypoints too early when transition could not be calculateed correctly - Fixed FWC incorrectly activating phase 9 on takeoff momentarily, causing inhibited messages to appear - Added ECAM procedure for fuel auto transfer fault February 19 2018 Release version 1.07b2 ======================================= - LNAV fixes - fixes for incorrect enroute distance calculations February 17 2018 Release version 1.07b1 ======================================= - Increased rudder trim reset speed - Added support for Poldragonet upper/lower ecam brightness, gravity gear extend and console/floor lights February 15 2018 Release version 1.06 ===================================== FMS: - Fixed Max and Recommended alt can go above limit - Fixed MDA an DH not clearable in PERF APPROACH - Fixed speed during hold was always green dot speed, even in approach - Added extra box and triple click when ALT* reverts to V/S if not acknowledged within 5 seconds - Added triple click for flight mode changes - Fixed crash on accessing INIT B Reserve fuel - Fixed Trip wind +/- reversal - Fixed an issue with altitude waypoints not calculating correctly Systems: - Fixed autothrust system for takeoff without F/D - Improved speedbrake effectiveness - Reset Elevator trim to 0 when ELAC 1 is reset on ground - Added stabilizer jam fault - Added ELEV failures - Status page should show AP inop during alignment - Allow engine start during "lever not idle" fault - Fixed button state not being set correctly when quickstart states are used - Fixed pitch stability issue causing slight pitch up in normal law - Retuning of FWB roll compensator - Fixed nose wheel was not operational if no FACs online - Improvements in single engine rudder and bank control - Improvements in rudder control - Fix for rudder flutter - Improved ECAM ALL button logic - Increased startup brake accu pressure to prevent ECAM warning on cold & dark startup - Fixed external power AVAIL light not showing up on light test - Added fuel selector control to simconnect link - Fix for incorrect mixture control through simconnect which could cause start failure Displays: - Decel marker should disappear after passing on ND - Fix for ProsimDisplay crash with ASN - Improvements in ECAM FCTL page, fctl surface readouts are no longer instantaneous - Minor speedtape cosmetic improvements - Fixed ADV showing in upper ECAM display incorrectly - Added dampening to speed tape acceleration vector - Logic for displaying map items on ND improved - Fixed display stutter when lots of FWC messages appear - Fixed FDS single channel radio writing frequencies incorrectly Flight guidance: - Alt hold mode will now command level off when CMD engages and alt deviation from FCU alt is more than 250 feet - Fixed early descend V/S always -1000 instead of -500 or -1000 - Fixed PFD alt bug not following FCU value when in ALT CRZ Hardware: - Fix for CPFlight FCU alt showing 0 at startup - Fixed FSCockpit EFIS backlight - Fixed FDS FCU Exped indicator not working - Added option to disable FSCockpit elevator trim motor Misc: - Enabled quickstart functionality - Added option to slave standby altimeter to Capt or F/O - Added airway data to the FMS XML call: http://localhost:8080/xml?query=fms - Fixed battery switches have incorrect startup state when hardware is of momentary type and quickstart is set to cold and dark - Default state of beacon state for cold & dark mode changed to off - Fix for BGL scanner failing on P3D v4 addons using relative paths - Fixed issue in parsing P3D v4 style addon scenery configuration for BGL scanner - Added scanning of add-on.xml based scenery paths from prepar3d v4 to BGLScanner - P3D v4 addons are prioritized over regular scenery.cfg addons in BGL scanner - Added extra matching algorithm for BGL data exports where runways are not linked to their ILS February 15 2018 Release version 1.06b27 ======================================== - Fix for simconnect events ont working properly February 14 2018 Release version 1.06b26 ======================================== - Fixed an issue with altitude waypoints not calculating correctly - Added fuel selector control to simconnect link February 13 2018 Release version 1.06b25 ======================================== - Fixed incorrect color of FLEX temperature on upper ECAM - Fixed FDS single channel radio writing frequencies incorrectly - Added extra matching algorithm for BGL data exports where runways are not linked to their ILS February 12 2018 Release version 1.06b24 ======================================== - Fix for incorrect mixture control through simconnect which could cause start failure February 10 2018 Release version 1.06b23 ======================================== - Fixed external power AVAIL light not showing up on light test - Increased startup brake accu pressure to prevent ECAM warning on cold & dark startup - Added option to disable FSCockpit elevator trim motor - Default state of beacon state for cold & dark mode changed to off February 8 2018 Release version 1.06b22 ======================================= - Fixed FDS FCU Exped indicator not working February 5 2018 Release version 1.06b21 ======================================= - Fix for BGL scanner failing on P3D v4 addons using relative paths February 3 2018 Release version 1.06b20 ======================================= - Improved ECAM ALL button logic - Fix for rudder flutter - Improvements in rudder control - Improvements in single engine rudder and bank control - Fixed battery switches have incorrect startup state when hardware is of momentary type and quickstart is set to cold and dark - Fixed Trip wind +/- reversal January 31 2018 Release version 1.06b19 ======================================= - Fixed nose wheel was not operational if no FACs online - Fixed FSCockpit EFIS backlight - Added airway data to the FMS XML call: http://localhost:8080/xml?query=fms - More engine start logging January 29 2018 Release version 1.06b18 ======================================= - Retuning of FWB roll compensator January 28 2018 Release version 1.06b17 ======================================= - Fixed pitch stability issue causing slight pitch up in normal law January 27 2018 Release version 1.06b16 ======================================= - Fixed display stutter when lots of FWC messages appear January 26 2018 Release version 1.06b15 ======================================= - Logic for displaying map items on ND improved - Added dampening to speed tape acceleration vector - Fixed crash on accessing INIT B Reserve fuel January 23 2018 Release version 1.06b14 ======================================= - Fixed PFD alt bug not following FCU value when in ALT CRZ - Fixed early descend V/S always -1000 instead of -500 or -1000 - Added extra box and triple click when ALT* reverts to V/S if not acknowledged within 5 seconds - Alt hold mode will now command level off when CMD engages and alt deviation from FCU alt is more than 250 feet - Fixed speed during hold was always green dot speed, even in approach January 22 2018 Release version 1.06b13 ======================================= - Fixed button state not being set correctly when quickstart states are used January 22 2018 Release version 1.06b12 ======================================= - Fixed MDA an DH not clearable in PERF APPROACH - Fixed ADV showing in upper ECAM display incorrectly January 14 2018 Release version 1.06b11 ======================================= - Allow engine start during "lever not idle" fault - Fixed Max and Recommended alt can go above limit - Status page should show AP inop during alignment January 14 2018 Release version 1.06b10 ======================================= - Added option to slave standby altimeter to Capt or F/O - Added stabilizer jam fault - Minor speedtape cosmetic improvements January 12 2018 Release version 1.06b9 ====================================== - Added triple click for flight mode changes - Enabled quickstart functionality January 11 2018 Release version 1.06b8 ====================================== - Reset Elevator trim to 0 when ELAC 1 is reset on ground January 10 2018 Release version 1.06b7 ====================================== - Added ELEV failures - P3D v4 addons are prioritized over regular scenery.cfg addons in BGL scanner January 10 2018 Release version 1.06b6 ====================================== - Fixed issue in parsing P3D v4 style addon scenery configuration for BGL scanner January 9 2018 Release version 1.06b5 ===================================== - Fix for CPFlight FCU alt showing 0 at startup - Added scanning of add-on.xml based scenery paths from prepar3d v4 to BGLScanner January 8 2018 Release version 1.06b4 ===================================== - Improvements in ECAM FCTL page, fctl surface readouts are no longer instantaneous - Improved speedbrake effectiveness December 30 2017 Release version 1.06b3 ======================================= - Added more logging for simconnect issues December 29 2017 Release version 1.06b2 ======================================= - Fix for ProsimDisplay crash with ASN - Fixed autothrust system for takeoff without F/D - Decel marker should disappear after passing on ND December 23 2017 Release version 1.06b1 ======================================= - Fix for ProsimDisplay crash with ASN December 22 2017 Release version 1.05 ===================================== FMS: - Fixed AIRPORT MCDU button - Reworked MCDU wind pages - Added support for hold at PPOS - Added DATA -> Closest airports - MCDU DATA -> waypoints/pilots waypoints added - Added interaction between DES WIND ground entry and PERF APPROACH wind data - Added SAT/ALT to cruise wind page - Added perf/idle factor - Fixed SEC PERF Data for APPR phase is shared with non SEC data - Fixed PERF FLEX temp cannot be removed - Improved LNAV calculations - Improved VNAV speed management - Improved LNAV drawing - New LNAV/VNAV distance and waypoint transition model - Improved direct to initial turning point calculation based on current bank - Added rendering of ALTN FPLN on ND - NAV autotuning is now reset when FMS position lost - Selecting a visual approach now created a CF leg on the runway centerline - Flap 3 managed approach speed should be F speed mark - Fixed FMA modes active on ground during intial startup - Fixed managed alt dot during Alt Crz - Improved calculation of decel point in approach - transitionAltitudes.xml file updated - FMS now requires FCU action before going into DES phase - FMC now calculates TOD when no arrival is selected - Inhibit flashing THR MCT in FMA during takeoff in engine out condition until green dot speed has been reached - Fixed unable to delete origin airport in flightplan - Improved criteria for showing T/D - Fixed incorrect Vls when slats locked - Added autosequencing for mod flightplan to prevent errors on insertion after overflying a waypoint Systems: - Brought a large number of ECAM logic to current standard - ECAM messages with timers are now dynamic - Added IDG low oil fault - Added decompression failures - Fixed Increasing cruise alt through FCU not working when destination < 200 nm - Added extra requirement for both engines to be operating for cat 3 dual capability - Added not idle start fault - Fixed issue when pressing EMER CANCEL button - Fixed dual channel SFCC fault causing elevator problems - Randomized battery charge on startup - Fixed yellow brake accumulator depressurizing too quickly - Added icing model and control - Fixed ECAM FWC state 10 not engaging after shutdown - Increased FMGC power transient buffers so they don't lose data on RAT deployment - Added configurable switch for external power - Improved APU auto exting test - Fixed APU auto extinguish not using fire bottles - Improvements to APU shutdown and cooldown - Added support for observer RMP - Added configurable switch for door control - Disallow max autobrake arming in the air - Fixed 180 degrees reversal of selected VOR course for prepar3dv4 - Fixed VHF frequencies rounding to 2 digits in prepar3dv4 - Fixed VHF 1 and 2 show identical values in prepar3dv4 - Fixed FACs use SFCC flap handle position instead of flap surface position to determine VFe - Fixed fuel pumps show temperorary fault after engagement - Added FCU channel faults - FCU/EFIS defaults to fixed modes when all channels fail - Added CLR to exit STS page - Added alternate brake functional test - Only run DU self test on ground - Light test added to clock - Added 5 callout audio - IRS updated to support automatic GPS alignment - Pack control valve should close when bleed air pressure is low - HP Bleed valve should close when fire button is out - Dual FADEC fault no longer shuts down engine - Improved auto-reconfiguration of DMC's for ECAM displays - Various electric reconfigurations Displays: - Many enhancements in ECAM pages - Improvements on PFD speedtape; including NEG symbol, landing elevation, decision height - ND crosstrack error upgraded to 2 decimal places - Added AVAIL flag after engine start - Fixed ND ADF1 symbol in lower left corner - Blue hyd pump now shows OFF instead of LO after powerup - Fixed heading bug incorrectly drawn offscale on ND in some situations - Fixed weather radar image in red - Tuning of upper ecam display - Fixed formatting of FMA V/S and FPA modes - Fixed ProSimDisplay crashing, when ASN is detected but radar.bin file is not found. - Fixed a display freezing issue - Inhibit track line on ND when NAV is armed and intercepting - Fixed speedtape number format - V/S is amber when excessive - Heading in PFD now always 3 characters wide - Fixed V/S readout moving outside of visible range - Changed ECAM FCTL trim legend "DOWN" to "DN" - Fixes to PFD drawing of lower portion Flight guidance: - Added EXPED functionality - Improved autopilot response in go around phase - Improved single engine go around autopilot control - Improved speed control during managed descend - Go Around phase now commands green dot speed - Improved autopilot control on go around initiation - Improved phase transition criterea from go around to clb - Improvements in go around SRS mode - Improvements to automatic engagement of managed modes on ground - Fixed A/THR disconnect ecam message during go around - Fixed managed Approach speed not working when A/P and F/D are off - Improved G/S tracking - Bank angle limited on single engine operation Hardware: - Fixed CPFlight FCU startup speed invalid - Fixed CPFlight FCU altitude mismatch between hardware and PFD - Fixed small issues for the ASPAirspace FCU driver - Added poldragonet driver - Fixed for Skalarki clock - Fixed Skalarki FCU V/S display to format 00oo - Calibration of Skalarki WX Tilt input - Upgraded skalarki library - Fixed Skalarki Backlighting issues - Increased Skalarki trim motor speed and updated power off mode - Elevator trim reset speed on the ground improved for Skalarki throttle - Fixed FSCockpit rudder axis not working on rudder card - Updates to lighting for FSCockpit hardware - Added support for FDS A322 RMP, ACP and XPDR - Fixes for FDS FCU layout 2 - Fixed FDS rudder trim L/R flickering - Enabled display brightness control for FDS MCDU - IOCP output buffer added - Fix for CockpitSonic Radios only showing 5 digits - Added option to invert trim motor in CockpitSonic throttle - Flight Illusion driver upgraded to native FT232. Please reconfigure driver - Added Flight Illusion advanced dialog with device renaming tool - Buffer added to pololu driver and output processing is now done by a separate thread - Fixed Hardware connector not displaying voltage correctly - Updates to prevent malfunctioning elevator trim reset on ground Misc: - Added door synchronisation for prepar3d - IOS fuel page now allows typing in exact fuel numbers - Added ATC Alt reporting switch - Fixed install evaluation links in version manager - Fixed hang when changing IOS server port in configuration screen - Fixed Navigraph reporting distances in VD Arinc 424 tracks in the "Distance" field instead of the "Navdist" field in the navigation database, causing SIDs/STARs to render incorrectly - Added option to reset FMS after landing - Weather radar through simconnect added (p3dv4). This is the default ProSim-A322 weather radar. ASN support for simconnect is not yet available. - Runways added to XML FMS query - Fixed issue with server validation - Fixed ProSimAudio consuming too much CPU time - Reset FMS query added to the XML entry point - Fixed simconnect invalid radio altimeter data - Fixed simconnect interface cargo weight adding passenger weight - Added various SDK control variables - Added warning for debug mode - Relay sounds added - Protection against invalid IAS data - Pushback in Prepar3dv4 no longer requires stop button to change direction - ASN support added to SimConnect link - Improved loading of FMS flightplans into company routes December 18 2017 Release version 1.05b86 ======================================== - Fixes to PFD drawing of lower portion - Added door synchronisation for prepar3d December 12 2017 Release version 1.05b85 ======================================== - IOS fuel page now allows typing in exact fuel numbers - Added perf/idle factor December 8 2017 Release version 1.05b84 ======================================= - Updates to prevent malfunctioning elevator trim reset on ground December 7 2017 Release version 1.05b83 ======================================= - Updated Skalarki library to 5.0.1460 - Elevator trim reset speed on the ground improved for Skalarki throttle December 4 2017 Release version 1.05b82 ======================================= - Added autosequencing for mod flightplan to prevent errors on insertion after overflying a waypoint - Updated Skalarki library to 5.0.1450 - Increased Skalarki trim motor speed and updated power off mode - Added ATC Alt reporting switch December 2 2017 Release version 1.05b81 ======================================= - Fixed for ECAM cold and dark status November 30 2017 Release version 1.05b80 ======================================== - Fixed rudder travel limiter fault on cold and dark startup - Fixed Poldragonet FCU metric alt button November 28 2017 Release version 1.05b79 ======================================== - Updated ECAM procedures for elec bus failures November 26 2017 Release version 1.05b78 ======================================== - Updated ECAM procedures - Improved ECAM synoptics in ELEC, HYD and FUEL pages November 23 2017 Release version 1.05b77 ======================================== - Fix for problems with stray dll files remaining in ProSimA322 system folder from previous pre-releases - Fix to prevent hickups in ProSimDisplay every second for systems without FSUIPC installed November 17 2017 Release version 1.05b76 ======================================== - Added support for hold at PPOS - Bank angle limited on single engine operation - Various electric reconfigurations November 17 2017 Release version 1.05b75 ======================================== - Fixed install evaluation links in version manager November 15 2017 Release version 1.05b74 ======================================== - Improved auto-reconfiguration of DMC's for ECAM displays - Changed ECAM FCTL trim legend "DOWN" to "DN" - Added ECAM data for FWC single channel failures - Fixed incorrect Vls when slats locked November 15 2017 Release version 1.05b73 ======================================== - Stability fix for FSUIPC connection access violation - Fixed V/S readout moving outside of visible range November 14 2017 Release version 1.05b72 ======================================== - Heading in PFD now always 3 characters wide - ECAM messages with timers are now dynamic - HP Bleed valve should close when fire button is out - Dual FADEC fault no longer shuts down engine - Enabled display brightness control for FDS MCDU November 11 2017 Release version 1.05b71 ======================================== - Range set to 80NM in case of FCU dual fault - Updated VOR/ADF pointers in case of FCU fault - Updated ECAM for FCU fault - Improved criteria for showing T/D - ECAM improvements November 11 2017 Release version 1.05b70 ======================================== - LNAV rendering improvements November 8 2017 Release version 1.05b68 ======================================= - Fixed issue with server validation November 8 2017 Release version 1.05b67 ======================================= - Additional logging for null ref exception - V/S is amber when excessive November 8 2017 Release version 1.05b66 ======================================= - Fix for Poldragonet hardware issues November 7 2017 Release version 1.05b65 ======================================= - Fixed hang when changing IOS server port in configuration screen - Fixed Navigraph reporting distances in VD Arinc 424 tracks in the "Distance" field instead of the "Navdist" field in the navigation database, causing SIDs/STARs to render incorrectly November 4 2017 Release version 1.05b62 ======================================= - Pack control valve should close when bleed air pressure is low - Inhibit track line on ND when NAV is armed and intercepting - Fixed speedtape number format November 1 2017 Release version 1.05b61 ======================================= - Added 5 callout audio - Fixed FDS rudder trim L/R flickering October 29 2017 Release version 1.05b60 ======================================= - Improvements on PFD speedtape; including NEG symbol, landing elevation, decision height - IRS updated to support automatic GPS alignment - Light test added to clock - ND crosstrack error upgraded to 2 decimal places October 28 2017 Release version 1.05b59 ======================================= - Fixed Issue with IOS route page October 27 2017 Release version 1.05b58 ======================================= - Fixed IOS issue October 27 2017 Release version 1.05b57 ======================================= - Fixed crash in simconnect link October 24 2017 Release version 1.05b56 ======================================= - Fixed unable to delete origin airport in flightplan - Added option to invert trim motor in CockpitSonic throttle October 22 2017 Release version 1.05b55 ======================================= - Fixed a display freezing issue - Added Flight Illusion advanced dialog with device renaming tool October 20 2017 Release version 1.05b54 ======================================= - Fixed Hardware connector not displaying voltage correctly October 17 2017 Release version 1.05b53 ====================================== - Added DATA -> Closest airports - Flight Illusion driver upgraded to native FT232. Please reconfigure driver - Added AVAIL flag after engine start October 13 2017 Release version 1.05b52 ====================================== - Fix for invalid date crash - Fix for CockpitSonic Radios only showing 5 digits October 12 2017 Release version 1.05b51 ====================================== - Buffer added to pololu driver and output processing is now done by a separate thread October 11 2017 Release version 1.05b50 ====================================== - Added alternate brake functional test October 8 2017 Release version 1.05b49 ====================================== - Fixed Skalarki Backlighting issues October 3 2017 Release version 1.05b48 ====================================== - FMC now calculates TOD when no arrival is selected October 2 2017 Release version 1.05b47 ====================================== - Inhibit flashing THR MCT in FMA during takeoff in engine out condition until green dot speed has been reached - Fixed PERF FLEX temp cannot be removed - Fixed formatting of FMA V/S and FPA modes - Fixed ProSimDisplay crashing, when ASN is detected but radar.bin file is not found. - Only run DU self test on ground September 27 2017 Release version 1.05b46 ========================================= - Fix for navigation data not working in some saves September 27 2017 Release version 1.05b45 ========================================= - Added option to reset FMS after landing - MCDU DATA -> waypoints/pilots waypoints added - Added CLR to exit STS page - Runways added to XML FMS query - ASN support added to SimConnect link September 19 2017 Release version 1.05b44 ========================================= - Fixed Skalarki backlighting when FCU fails - Fixed crash after resetting FMS September 13 2017 Release version 1.05b43 ========================================= - FMS now requires FCU action before going into DES phase - Weather radar through simconnect added (p3dv4). This is the default ProSim-A322 weather radar. ASN support for simconnect is not yet available. September 13 2017 Release version 1.05b42 ========================================= - Upgraded skalarki library - Fixes for FDS FCU layout 2 September 12 2017 Release version 1.05b41 ========================================= - New LNAV/VNAV distance and waypoint transition model - Improved G/S tracking September 9 2017 Release version 1.05b40 ======================================== - Removed FSUIPC background processing September 6 2017 Release version 1.05b39 ======================================== - IOCP output buffer added - Improved LNAV drawing - Fixed ND ADF1 symbol in lower left corner - FCU/EFIS defaults to fixed modes when all channels fail September 5 2017 Release version 1.05b38 ======================================== - transitionAltitudes.xml file updated - Added FCU channel faults - Improved calculation of decel point in approach - Improved LNAV calculations - Improved VNAV speed management August 30 2017 Release version 1.05b37 ====================================== - Fixed fuel pumps show temperorary fault after engagement - FSUIPC driver is now processed in a background thread to prevent excessive processing time - Fix for engines not starting August 28 2017 Release version 1.05b36 ====================================== - Calibration of Skalarki WX Tilt input - Potential fix for engine not starting - Improvements to automatic engagement of managed modes on ground August 25 2017 Release version 1.05b35 ====================================== - Fixed CPFlight FCU altitude mismatch between hardware and PFD August 24 2017 Release version 1.05b34 ====================================== - Fixed FACs use SFCC flap handle position instead of flap surface position to determine VFe - Fixed Skalarki FCU V/S display to format 00oo - Fixed ProSimAudio consuming too much CPU time August 21 2017 Release version 1.05b33 ====================================== - Fixed managed alt dot during Alt Crz - Improvements to APU shutdown and cooldown August 19 2017 Release version 1.05b32 ====================================== - Updates to upper ECAM flap block - Updates to lighting for FSCockpit hardware August 19 2017 Release version 1.05b31 ====================================== - Fixed 180 degrees reversal of selected VOR course for prepar3dv4 - Fixed APU auto extinguish not using fire bottles - Fixed VHF frequencies rounding to 2 digits in prepar3dv4 - Fixed VHF 1 and 2 show identical values in prepar3dv4 August 18 2017 Release version 1.05b30 ====================================== - Disallow max autobrake arming in the air - Added configurable switch for door control - Fixed FMA modes active on ground during intial startup - Increased FMGC power transient buffers so they don't lose data on RAT deployment August 16 2017 Release version 1.05b29 ====================================== - Added support for observer RMP - Flap 3 managed approach speed should be F speed mark - Added configurable switch for external power - Tuning of upper ecam display August 15 2017 Release version 1.05b28 ====================================== - Added support for FDS A322 RMP, ACP and XPDR August 14 2017 Release version 1.05b27 ====================================== - Reset FMS query added to the XML entry point - Fixed ECAM FWC state 10 not engaging after shutdown - Fixed managed Approach speed not working when A/P and F/D are off - Pushback in Prepar3dv4 no longer requires stop button to change direction - Selecting a visual approach now created a CF leg on the runway centerline - NAV autotuning is now reset when FMS position lost August 11 2017 Release version 1.05b26 ====================================== - Fixed yellow brake accumulator depressurizing too quickly - Improved ECAM HYD page - Blue hyd pump now shows OFF instead of LO after powerup - ECAM updates - Fixed heading bug incorrectly drawn offscale on ND in some situations - Fixed dual channel SFCC fault causing elevator problems August 9 2017 Release version 1.05b25 ===================================== - Fixes in ELEC ECAM page August 3 2017 Release version 1.05b23 ===================================== - Fixed weather radar image in red August 3 2017 Release version 1.05b22 ===================================== - Relay sounds added - Protection against invalid IAS data August 1 2017 Release version 1.05b21 ===================================== - Added interaction between DES WIND ground entry and PERF APPROACH wind data - Randomized battery charge on startup - Added icing model and control - Fixed simconnect invalid radio altimeter data July 26 2017 Release version 1.05b20 ==================================== - Fixed FSCockpit rudder axis not working on rudder card - Reworked MCDU wind pages - Added SAT/ALT to cruise wind page - Fixed SEC PERF Data for APPR phase is shared with non SEC data July 24 2017 Release version 1.05b19 ==================================== - Added warning for debug mode - Fixed issue when pressing EMER CANCEL button July 23 2017 Release version 1.05b18 ==================================== - Added not idle start fault - ECAM updates July 19 2017 Release version 1.05b17 ==================================== - Fixed CPFlight FCU startup speed invalid - Added rendering of ALTN FPLN on ND July 18 2017 Release version 1.05b15 ==================================== - Added extra requirement for both engines to be operating for cat 3 dual capability July 17 2017 Release version 1.05b14 ==================================== - Fixed AIRPORT MCDU button July 17 2017 Release version 1.05b13 ==================================== - Improved APU auto exting test - Improved direct to initial turning point calculation based on current bank - Fixed Increasing cruise alt through FCU not working when destination < 200 nm - Added various SDK control variables - Added decompression failures July 14 2017 Release version 1.05b12 ==================================== - Added IDG low oil fault - Fixed simconnect interface cargo weight adding passenger weight - Improved single engine go around autopilot control - Brought a large number of ECAM logic to current standard - Added EXPED functionality July 7 2017 Release version 1.05b11 =================================== - Improved autopilot response in go around phase July 5 2017 Release version 1.05b10 =================================== - Improved speed control during managed descend - Go Around phase now commands green dot speed - Improved autopilot control on go around initiation - Improved phase transition criterea from go around to clb July 1 2017 Release version 1.05b9 ================================== - Improved loading of FMS flightplans into company routes June 30 2017 Release version 1.05b8 =================================== - Improvements in go around SRS mode - Fixed A/THR disconnect ecam message during go around June 28 2017 Release version 1.05b7 =================================== - Fixed small issues for the ASPAirspace FCU driver June 26 2017 Release version 1.05b6 =================================== - Added poldragonet driver June 24 2017 Release version 1.05b2 =================================== - Fixed for Skalarki clock June 23 2017 Release version 1.04 ================================= Quickfix for versionmanager not seeing non beta releases as latest release. - Added support for skalarki clock - Added skalarki EFIS QNH indicator - Fixed RDME showing true heading instead of magnetic June 20 2017 Release version 1.03 ================================= FlightModel: - Enabled sidestick augmentation option Note on tuning sidesticks: In the default configuration of 0 augmentation, the sidesticks in ProSimA322-system are tuned to have proper flightcharacteristics based on the deflection of the sidestick. The real A322 sidesticks however are very stiff. If a simulator has too little force in the sidestick, proper force input on this stick will lead to an exaggerated motion on the sidestick, giving the illusion that the aircraft is over-sensitive. This problem may be overcome by setting a negative sidestick augementation, causing the sidesticks to report a lower input signal. Using augmentation however is not ideal and can only be used to reduce the effect of exaggerated sidestick output. Properly loaded sidesticks should use an augmentation value of 0. Flight guidance: - Selected speed during approach can go below F/S/GD speed - SRS should command v2+15 max during single engine - Increased flare response during autoland - Improved engine out SRS logic and managed speed targets - VS/FPA available when FCU alt is current alt - Lateral path improvements for approaches - Improved pitch stability in turns - Fixed normal law does not maintain altitude between 30 and 33 degrees bank - Fixed VD leg types not handled correctly - Added FMS bypass logic for intercept legs to prevent flyover of intercept point - Fixed route markers appearing outside of route in ND - Added speed limit indications on ND track - Improved rollout autopilot - Fixed issue where MCDU NEXT WPT does not enter waypoint correctly - Improvements in vertical profile calculation and stability during turns - Fixed Manual termination legs not rendering correctly and causing incorrect fuel calculations - Fixed issue where ILS's would not function correctly on runways that have different runway identifiers in airac database as in in BGL scenery database - Fixed managed climb does not initiate climb when cruise altitude changed through FCU - Improved later track intercept - Added workaround for incorrectly coded arc legs in navigation database - Only allow G/S capture when LOC is fully established - Tuning of localiser capture - Tuning of vertical speed vs acceleration during climb - Protection against high cabin v/s after reposition - Fixed issues with selected alt mode not engaging during managed cruise - Fixed managed CLB not engaging after takeoff - SRS should remain active on engine failure - SRS reverts to open climb when speed is selected - Fixed speed calculation for holdings - Fixed ALT* annunciated as ALT CST* at cruise alt - Fixed spoiler not working while in flight - Pitch stability enhancement in manual flight MCDU: - Fixed CDU FPLN pages scroll back to top when modifying data - Improvements and additions to the SEC system - Fixed ZFW entries accepting invalid values - Added approach VIAs - Added "Check take off data" message - Fixed FPLN VNAV data not available after T/C when no T/D present - Fixed issue with sequencing waypoints when a leg was skipped - Fixed crash on entering a waypoint to an empty flightplan - MCDU will now clear scratchpad when CLR held down - Fixed ordering of approaches based on approach types - Fixed manually inserted missed approach legs not recognized as missed approach - Fixed destination disappears when no star or approach selected at destination and star is inserted - RNAV approaches are now recognized as non precision Prepar3d v4: - Added simconnect simulator connection option for prepar3dv4. Setting 'simulator' to 'simconnect' in ProSimA322-system will remove the dependency on FSUIPC. Hardware: - Added driver for SimASPAirSpace FCU - Fixed synchronisation issue in CPFlight FCU where alt scale turned down to 100 - Fixed crash when setting incorrect radio active on RMP - Fixed initial altitude on CPFlight FCU - Generic com driver added - Added option for momentary fire buttons for Cockpit Sonic overhead panel - Added support for FSCockpit old MCDU layout - Added option for FSCockpit FCU alt scale reversal - Added refuel panel - Added support for Skalarki pushback panel - Updated Skalarki version to 5.0.1430 - Added option for Cockpitsonic MCDU old keyboard layout - Added support for Cockpitsonic clock - Fixed cockpit sonic external light switch id's - Fixed cockpitsonic speedbrake arm switch - Fix for cockpitsonic gear lever - Fix for cockpitsonic elevator trim motor - Added option for reversing FSCockpit EFIS switches - Changed Cockpitsonic trim wheel configuration to support stepper motor output with calibration - Added FSCockpit MIP Terrain indicators - Added FSCockpit rudder trim test pattern - Fixed CockpitSonic RMP display and encoder - Fixed CockpitSonix indicator/display brightness - Fixed issue with where FSCockpit hardwareconnector module would not report axes data - Added FSCockpit light test support for displays - Fixed FSCockpit inversed trim - Fixed FSCockpit inverted APU switch lights - Added FSCockpit terrain switches - Added FSCockpit gear reversal option - Fixed FSCockpit FD/ND captain brightness reversed - Fixed CPflight FCU does not synchronized speed or heading when moving from managed to selected mode - Added support for FDS A322 clock - Added support for alternate FDS FCU F/O EFIS indicator layout - Added support for FSCockpit hardware in the HardwareConnector module - Fix for CPFlight FCU firmware 1.16 encoder issues - Fixed EHID F/O sidestick pitch not functioning - Added brake triple gauge gauges for configuration with EHID or other gauge hardware - Added Skalarki cargo hot air indicators - Added EHID MIP GPWS TERR buttons and GPWS visual alert buttons - Fixed EHID Captain RMP standby display - Fixed Skalarki hot air buttons - Added SIOC MCDU function keys - Fixed FDS transponder backlight not enabled - Added FDS ATC L/R switch - Fix for FDS radio decimal point location - Added ability to set speedbrake ARM position on the speedbrake axis Systems: - Added Lavatory/Galley extraction fan fault - Upgraded pressurisation/ventilation from Pack Controllers to newer ACSC system - Fixed IDG overheat when fuel freeze is on - Slides are now dynamically armed based on aircraft condition - RCRD ground ctl should switch off at engine start - Refined inop spoiler logic and ECAM - Fuel system improvements - Addded Aft overhead fadec, blue pump override and leak measurement valves - ECAM should show wheel page on ground after engine start - Added extra gear failures - Improved gear hydraulic model - Improved PTU performance - Fixed blue hyd pump requires engine N2 > 50 - Added analog and switch inputs for gravity gear extend - Fixed ELAC's won't operate pitch channel if opposite elevator is uncontrollable - Improved FMA ground reset criterea - Added further TCAS functionality - Added EIU - Added ECAM status engine relight information - Added FD disengagement criterea - Fixed speedtape next flap placard speed for flap 1 should be flap 2 instead of 1+f - Fixed DME-only stations not showing DME in ND - Added Backup speed/alt mode option - Added ECAM cruise cargo heat synoptics - Added option for Adiru IR1, IR2 and IR3 switches with FAULT/OFF indicators - Fixed APU start fault - Fixed BAT OFF light not illuminating when both batteries off and power available - Tuned internal IDG heat generation - Tuned ECAM symbols - Added cargo heat option - Tuning of trim air valves - Fixed stuttering cockpit hot air trim valve - Added IDG overheat fault Misc: - Added check items to IOS - Added slide control in IOS - Log added to web server - Option to detect FS added to the database window - Sim path is now saved in ProSim Config - High quality terrain added - Added external power control to XML interface - Added gates for v1, vr and v2 - Added remote computer shutdown option to ProSim Audio and ProSimA322-system - Fixed PFD and ND not drawing offscale FCU headings - Route must also be drawn solid when LOC mode is active - LNAV drawing improvements - Fixed configuration not saving trim motor output - Added gates for second dome light - Added configurable inputs for QNH settings - Added quickset buttons to switch types configuration screen - Added IOS nosewheel steering pin option - Renamed incorrectly named F/O inboard power switch - Fixed incorrect flap settings - Fixed ND zoom scale in rose mode - Added PFD non lineair pitch scale below -10 degrees - Increased draw area below aircraft symbol on ND in arc mode - Added speedbrake Vls scaling - Added APU N% numerical output - Added gates for brake indicator zero/nonzero - Added gates for emergency lights - Added ECAM brightness display dials to ProSim Display - Fix for ECAM press page red cross when outflow valve is fully open - Added individual DIM and BRT dome light gates - Added ProSim Display clock graphics and brake triple gauge graphics - Added APU sound gates - Fixed ProSimDisplay issue during alt capture of cruise altitude - Fixed Terrain not working correctly at high altitude airports - Fixed issue with hardwareconnector not working after ProSimA322 restart - Increase compatibility with addons relying on actual parking brake to be set - Updated ECAM panel graphics - Fixed missing REV indicator in EPR gauge - Fixed some elements not shown when TERRAIN ON ND active. - Added frontcourse indicator to ND - Improved offscale frontcourse indicator in PFD headingtape - Tuning of PFD and ND symbols - Added missing offscale V1 speed in speedtape - Added various SDK variables - Added cache control meta tags to IOS page - Added analog dial for manual cabin altitude control to ECAM cruise page - Added various environmental gates for addon sounds - Activated remote shutdown feature - Tuning for evaluation flight model - Added web access URLs menu item - Fixed heading bug in PFD not displayed when ILS received and LS button on - Fixed mislabeled ENG 1 FIRE in engine 2 ECAM - New ECAM data June 15 2017 Release version 1.03b92 ==================================== - Fixed simconnect magnetic variation error in heading display - Fixed CDU FPLN pages scroll back to top when modifying data June 14 2017 Release version 1.03b91 ==================================== - Fix for simconnect repositioning always places aircraft on ground June 14 2017 Release version 1.03b89 ==================================== - Fixed SimConnect COM radios not working - Fixed scenery not reloading on reposition with simconnect June 13 2017 Release version 1.03b88 ==================================== - Improvements and additions to the SEC system June 8 2017 Release version 1.03b86 =================================== - Selected speed during approach can go below F/S/GD speed - SRS should command v2+15 max during single engine May 31 2017 Release version 1.03b85 =================================== - Added lighting control to simconnect link May 30 2017 Release version 1.03b84 =================================== - Added simconnect simulator connection option for prepar3dv4. Setting 'simulator' to 'simconnect' in ProSimA322-system will remove the dependency on FSUIPC. May 30 2017 Release version 1.03b83 =================================== - Increased flare response during autoland - Added FMS bypass logic for intercept legs to prevent flyover of intercept point May 27 2017 Release version 1.03b82 =================================== - Improved engine out SRS logic and managed speed targets - VS/FPA available when FCU alt is current alt May 25 2017 Release version 1.03b81 =================================== - Added driver for SimASPAirSpace FCU May 24 2017 Release version 1.03b80 =================================== - Added check items to IOS - Lateral path improvements for approaches May 20 2017 Release version 1.03b79 =================================== - Improved pitch stability in turns May 17 2017 Release version 1.03b77 =================================== - Fixed synchronisation issue in CPFlight FCU where alt scale turned down to 100 - Added Lavatory/Galley extraction fan fault - Upgraded pressurisation/ventilation from Pack Controllers to newer ACSC system - Fixed crashes in CDU code - Fixed crash when setting incorrect radio active on RMP - Fixed initial altitude on CPFlight FCU - Fixed IDG overheat when fuel freeze is on - Fixed normal law does not maintain altitude between 30 and 33 degrees bank May 12 2017 Release version 1.03b76 =================================== - Fixed VD leg types not handled correctly - Generic com driver added - Added option for momentary fire buttons for Cockpit Sonic overhead panel - Added slide control in IOS May 10 2017 Release version 1.03b75 ================================== - Fixed ZFW entries accepting invalid values - Slides are now dynamically armed based on aircraft condition - Added support for FSCockpit old MCDU layout May 9 2017 Release version 1.03b74 ================================== - Added option for FSCockpit FCU alt scale reversal May 1 2017 Release version 1.03b73 ================================== - Fixed route markers appearing outside of route in ND - RCRD ground ctl should switch off at engine start May 1 2017 Release version 1.03b71 ================================== - Log added to web server - Option to detect FS added to the database window - Sim path is now saved in ProSim Config - High quality terrain added - Added refuel panel - Added support for Skalarki pushback panel - Added speed limit indications on ND track - Improved rollout autopilot April 27 2017 Release version 1.03b70 ===================================== - Added external power control to XML interface April 25 2017 Release version 1.03b69 ===================================== - Added approach VIAs April 22 2017 Release version 1.03b68 ===================================== - Added "Check take off data" message - Added gates for v1, vr and v2 - Added remote computer shutdown option to ProSim Audio and ProSimA322-system - Fixed FPLN VNAV data not available after T/C when no T/D present April 20 2017 Release version 1.03b67 ===================================== - Updated Skalarki version to 5.0.1329 April 19 2017 Release version 1.03b66 ===================================== - Added option for Cockpitsonic MCDU old keyboard layout - Refined inop spoiler logic and ECAM - Fixed issue where MCDU NEXT WPT does not enter waypoint correctly April 16 2017 Release version 1.03b65 ===================================== - Improvements in vertical profile calculation and stability during turns April 13 2017 Release version 1.03b64 ===================================== - Fixed PFD and ND not drawing offscale FCU headings - Fixed Manual termination legs not rendering correctly and causing incorrect fuel calculations April 12 2017 Release version 1.03b63 ===================================== - Fixed issue with sequencing waypoints when a leg was skipped - Route must also be drawn solid when LOC mode is active April 10 2017 Release version 1.03b62 ==================================== - LNAV drawing improvements - Fuel system improvements April 5 2017 Release version 1.03b61 ==================================== - Enabled sidestick augmentation option Note on tuning sidesticks: In the default configuration of 0 augmentation, the sidesticks in ProSimA322-system are tuned to have proper flightcharacteristics based on the deflection of the sidestick. The real A322 sidesticks however are very stiff. If a simulator has too little force in the sidestick, proper force input on this stick will lead to an exaggerated motion on the sidestick, giving the illusion that the aircraft is over-sensitive. This problem may be overcome by setting a negative sidestick augementation, causing the sidesticks to report a lower input signal. Using augmentation however is not ideal and can only be used to reduce the effect of exaggerated sidestick output. Properly loaded sidesticks should use an augmentation value of 0. April 4 2017 Release version 1.03b60 ==================================== - Fixed configuration not saving trim motor output April 4 2017 Release version 1.03b59 ==================================== - Fixed crash on entering a waypoint to an empty flightplan March 31 2017 Release version 1.03b58 ===================================== - Addded Aft overhead fadec, blue pump override and leak measurement valves March 28 2017 Release version 1.03b57 ===================================== - Added support for Cockpitsonic clock - Fixed cockpit sonic external light switch id's March 28 2017 Release version 1.03b54 ===================================== - Fixed cockpitsonic speedbrake arm switch March 25 2017 Release version 1.03b53 ===================================== - Fix for cockpitsonic gear lever - Fix for cockpitsonic elevator trim motor March 25 2017 Release version 1.03b49 ===================================== - Added gates for second dome light March 23 2017 Release version 1.03b48 ===================================== - Added option for reversing FSCockpit EFIS switches - Changed Cockpitsonic trim wheel configuration to support stepper motor output with calibration - Added configurable inputs for QNH settings March 17 2017 Release version 1.03b47 ===================================== - Added quickset buttons to switch types configuration screen - Added FSCockpit MIP Terrain indicators - Added FSCockpit rudder trim test pattern - Fixed CockpitSonic RMP display and encoder - Fixed CockpitSonix indicator/display brightness March 17 2017 Release version 1.03b46 ===================================== - Updated Skalarki version to 5.0.1327 March 15 2017 Release version 1.03b45 ===================================== - Added IOS nosewheel steering pin option - Fixed issue with where FSCockpit hardwareconnector module would not report axes data - Fixed issue where ILS's would not function correctly on runways that have different runway identifiers in airac database as in in BGL scenery database March 13 2017 Release version 1.03b43 ===================================== - Added FSCockpit light test support for displays - Fixed FSCockpit inversed trim - Fixed FSCockpit inverted APU switch lights - Added FSCockpit terrain switches - Added FSCockpit gear reversal option - Fixed FSCockpit FD/ND captain brightness reversed March 10 2017 Release version 1.03b42 ===================================== - Renamed incorrectly named F/O inboard power switch - Fixed incorrect flap settings March 3 2017 Release version 1.03b41 ==================================== - Updated Skalarki version to 5.0.1326 March 3 2017 Release version 1.03b40 ==================================== - Fixed CPflight FCU does not synchronized speed or heading when moving from managed to selected mode - Fixed managed climb does not initiate climb when cruise altitude changed through FCU - MCDU will now clear scratchpad when CLR held down - Fixed ND zoom scale in rose mode - Added PFD non lineair pitch scale below -10 degrees February 26 2017 Release version 1.03b38 ======================================== - Fixed ordering of approaches based on approach types - Fixed manually inserted missed approach legs not recognized as missed approach - Fixed destination disappears when no star or approach selected at destination and star is inserted - Improved later track intercept February 25 2017 Release version 1.03b36 ======================================== - Added workaround for incorrectly coded arc legs in navigation database - Increased draw area below aircraft symbol on ND in arc mode February 22 2017 Release version 1.03b35 ======================================== - Added speedbrake Vls scaling February 21 2017 Release version 1.03b34 ======================================== - RNAV approaches are now recognized as non precision February 21 2017 Release version 1.03b33 ======================================== - Only allow G/S capture when LOC is fully established - Tuning of localiser capture - Tuning of vertical speed vs acceleration during climb - Protection against high cabin v/s after reposition February 21 2017 Release version 1.03b32 ======================================== - Added support for FDS A322 clock - Added support for alternate FDS FCU F/O EFIS indicator layout February 17 2017 Release version 1.03b31 ======================================== - Fixed issues with selected alt mode not engaging during managed cruise - ECAM should show wheel page on ground after engine start - Fixed managed CLB not engaging after takeoff February 17 2017 Release version 1.03b30 ======================================== - Added extra gear failures - Improved gear hydraulic model - Improved PTU performance February 14 2017 Release version 1.03b29 ======================================== - Fixed blue hyd pump requires engine N2 > 50 - SRS should remain active on engine failure - SRS reverts to open climb when speed is selected February 14 2017 Release version 1.03b28 ======================================== - Added APU N% numerical output February 11 2017 Release version 1.03b27 ======================================== - Added analog and switch inputs for gravity gear extend - Added gates for brake indicator zero/nonzero February 10 2017 Release version 1.03b26 ======================================== - Improved fuel model - Fixed ELAC's won't operate pitch channel if opposite elevator is uncontrollable - Added support for FSCockpit hardware in the HardwareConnector module February 07 2017 Release version 1.03b25 ======================================== - Improved FMA ground reset criterea - Added gates for emergency lights - Added further TCAS functionality February 02 2017 Release version 1.03b24 ======================================== - Added ECAM brightness display dials to ProSim Display January 31 2017 Release version 1.03b22 ======================================= - Fix for ECAM press page red cross when outflow valve is fully open - Fix for CPFlight FCU firmware 1.16 encoder issues January 27 2017 Release version 1.03b21 ======================================= - Added EIU - Added ECAM status engine relight information - Added FD disengagement criterea January 26 2017 Release version 1.03b20 ======================================= - Added individual DIM and BRT dome light gates - Fixed EHID F/O sidestick pitch not functioning - Fixed speedtape next flap placard speed for flap 1 should be flap 2 instead of 1+f - Added ProSim Display clock graphics and brake triple gauge graphics - Added APU sound gates - Added brake triple gauge gauges for configuration with EHID or other gauge hardware - Fixed DME-only stations not showing DME in ND January 25 2017 Release version 1.03b19 ======================================= - Added Backup speed/alt mode option - Added Skalarki cargo hot air indicators January 24 2017 Release version 1.03b17 ======================================= - Added EHID MIP GPWS TERR buttons and GPWS visual alert buttons - Fixed EHID Captain RMP standby display - Fixed Skalarki hot air buttons January 23 2017 Release version 1.03b16 ======================================= - Added ECAM cruise cargo heat synoptics - Fixed ProSimDisplay issue during alt capture of cruise altitude - Added option for Adiru IR1, IR2 and IR3 switches with FAULT/OFF indicators January 23 2017 Release version 1.03b15 ======================================= - Added SIOC MCDU function keys - Fixed Terrain not working correctly at high altitude airports January 19 2017 Release version 1.03b14 ======================================= - Fixed APU start fault January 18 2017 Release version 1.03b13 ======================================= - Fixed speed calculation for holdings - Fixed FDS transponder backlight not enabled - Added FDS ATC L/R switch - Fixed BAT OFF light not illuminating when both batteries off and power available January 13 2017 Release version 1.03b12 ======================================= - Fixed ALT* annunciated as ALT CST* at cruise alt - Fixed spoiler not working while in flight - Tuned internal IDG heat generation - Tuned ECAM symbols January 13 2017 Release version 1.03b11 ======================================= - Fixed missing ProSim Display panels January 13 2017 Release version 1.03b10 ======================================= - Added cargo heat option - Tuning of trim air valves January 13 2017 Release version 1.03b9 ====================================== - Fixed issue with hardwareconnector not working after ProSimA322 restart January 13 2017 Release version 1.03b8 ====================================== - Increase compatibility with addons relying on actual parking brake to be set - Updated ECAM panel graphics - Fixed missing REV indicator in EPR gauge - Fixed some elements not shown when TERRAIN ON ND active. January 12 2017 Release version 1.03b7 ====================================== - Added frontcourse indicator to ND - Improved offscale frontcourse indicator in PFD headingtape - Tuning of PFD and ND symbols - Added missing offscale V1 speed in speedtape - Added various SDK variables January 9 2017 Release version 1.03b6 ===================================== - Added cache control meta tags to IOS page - Fixed stuttering cockpit hot air trim valve - Added IDG overheat fault - Added analog dial for manual cabin altitude control to ECAM cruise page - Added various environmental gates for addon sounds January 6 2017 Release version 1.03b5 ===================================== - Fix for FDS radio decimal point location - Activated remote shutdown feature January 6 2017 Release version 1.03b4 ===================================== - Tuning for evaluation flight model January 6 2017 Release version 1.03b3 ===================================== - Added web access URLs menu item - Fixed heading bug in PFD not displayed when ILS received and LS button on January 5 2017 Release version 1.03b2 ===================================== - Fixed mislabeled ENG 1 FIRE in engine 2 ECAM - New ECAM data January 4 2017 Release version 1.03b1 ===================================== Please recalibrate speedbrake lever - Added ability to set speedbrake ARM position on the speedbrake axis - Pitch stability enhancement in manual flight January 4 2017 Release version 1.02 =================================== - Fixed issue with updating ProSimA322-Audio January 3 2017 Release version 1.01 =================================== - Fixed issue with connecting the ProSimA230-HardwareConnector January 2 2017 Release version 1.00 =================================== ProSimA322 version 1.00 initial release